Figure 3 Oil pump, Release valve, Manifold, Tappets

Figure 3 Oil pump, Release valve, Manifold, Tappets
9 May 2023

Figure 3 Oil pump, Release valve, Manifold, Tappets

70-9421 / E9421
Oil pump assembly
Ref# 1 Fig. 3 Page 17 #7 (1969) (Req:1)
Timing chest

Oil pump body REF
Ref# 2 Fig. 3 Page 17 #7 (1969) (Req:1)
Timing chest

70-9269 / E9269
Oil pump feed plunger
Ref# 3 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil pump

70-6681 / E6681
Oil pump scavenge plunger
Ref# 4 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil pump

70-0495 / E495
Oil pump drive block
Ref# 5 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil pump
¹ Haynes says replace when removed

S70-7
Oil pump valve ball (7/32 in. dia.)
Ref# 6 Fig. 3 Page 17 #7 (1969) (Req:2)
Oil pump

70-0403 / E403
Oil pump valve spring
Ref# 7 Fig. 3 Page 17 #7 (1969) (Req:2)
Oil pump

70-2360 / E2360
Oil pump screwed plug
Ref# 8 Fig. 3 Page 17 #7 (1969) (Req:2)
Oil pump

70-3730 / E3730
Bin D-5 (3/0/0)
Joint washer
Ref# 9 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil pump
¹ No gasket sealer necessary

21-1864 / S1864
Stud, oil pump BSW/BSF 1/4-20TPI/26TPI X 1-5/16
Ref# 10 Fig. 3 Page 17 #7 (1969) (Req:2)
Oil pump body

70-3887 / E3887
Bin - (4/0/0)
Washer, serrated Serrated/conical
Ref# 11 Fig. 3 Page 17 #7 (1969) (Req:2)
Oil pump

21-1906 / S1906
Bin - (2/0/0)
Nut, conical UNF (SAE) 1/4-28TPI
Ref# 12 Fig. 3 Page 17 #7 (1969) (Req:2)
Oil pump
Torque: 5 LBS

70-6595 / E6595
OIL RELEASE VALVE ASSEMBLY
Ref# 13 Fig. 3 Page 17 #7 (1969) (Req:1)
Timing cover

70-7590 / E7590
Valve body (Tool-1")
Ref# 14 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil release valve

GS251
Piston
Ref# 15 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil release valve

70-6596 / E6596
Nut, domed (release valve cap) (Tool-15/16)
Ref# 16 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil release valve, crankcase T.S.

GS254
Bin D-3 (2/0/0)
Washer, fiber
Ref# 17 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil release valve (beneath Cap 17/16)

70-7591 / E7591
Spring
Ref# 18 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil release valve

70-1670 / E1670
Bin D-3 (3/0/0)
Washer, fiber 7/8"x1-1/16"x.39"
Ref# 19 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil release valve

70-9352 / E9352
Guide, tapet
Ref# 30 Fig. 3 Page 17 #7 (1969) (Req:1)
Inlet

70-9353 / E9353
Guide, tapet
Ref# 31 Fig. 3 Page 17 #7 (1969) (Req:1)
Exhaust

70-2440 / E2440
Washer, copper
Ref# 32 Fig. 3 Page 17 #7 (1969) (Req:2)
Tappet guide set bolt

97-0200 / H200
Bolt (tappet guide)
Ref# 33 Fig. 3 Page 17 #7 (1969) (Req:2)
Tappet guide set bolt

70-3059R / E3059R
Bin O-1 (0/2/2)
Tappet, inlet "R" Radius
Ref# 34 Fig. 3 Page 17 #7 (1969) (Req:2)
Tappet guide block

70-8801 / E8801
Bin O-1 (0/0/0)
Tappet, exhaust
Ref# 35 Fig. 3 Page 17 #7 (1969) (Req:2)
Tappet guide block
Orient: Machined cutaways (oil feed hole) must face OUT.

70-7563 / E7563
Bin D-1 (4/0/0)
O-ring Viton/Dash#20/Nom.CS 1/16"/ID 7/8"
Ref# 36 Fig. 3 Page 17 #7 (1969) (Req:2)
Tappet guide

EOF