All Parts,<br><font size=-1>by Part Number</font>

All Parts,
by Part Number
9 May 2023

AMAL 244/1048
Bin M-4 (7/0/0)
O-ring Thick
Ref# 3 Fig. 30#6 (1968) (Req:2)
Carburetter flange
¹ '68 & older - Monoblock, use w insul block & paper gasket

Oil pump body REF
Ref# 2 Fig. 3 Page 17 #7 (1969) (Req:1)
Timing chest

Damper unit REF
Ref# 17 Fig. 13 Page 37 #7 (1969) (Req:2)
Rear shock absorber

Brake lining (ref only) REF
Ref# 21 Fig. 19 Page 49 #7 (1969) (Req:2)
Front brake

Rivet, brass REF
Ref# 22 Fig. 19 Page 49 #7 (1969) (Req:16)
Front brake lining (ref only)

Brake lining REF
Ref# 27 Fig. 20 Page 51 #7 (1969) (Req:2)
Rear brake

Brass rivets REF
Ref# 28 Fig. 20 Page 51 #7 (1969) (Req:16)
Rear brake

Grip, twist grip REF
Ref# 11 Fig. 27 Page 63 #7 (1969) (Req:1)
Handlebars
¹ See Ref.34.

NORTON 06-7230
Bin - (1/0/0)
Grip, handlebar left REF
Ref# 34 Fig. 27 Page 63 #7 (1969) (Req:1)
Handlebars
¹ Norton PN 06-7230 is Gran-Turismo, Black, 7/8"

Mixing chamber REF
Ref# 2 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R

Stud, carburetter mounting REF (1 in.)
Ref# 32 Fig. 31 Page 71 #7 (1969) (Req:4)
Carburetter mounting flange T120R

Bush, driving gear (ref only) REF
Ref# 18 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach gear housing T120R-TR6R

Bush, tach driven gear (ref only) REF
Ref# 26 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach driven gear housing T120R-TR6R
¹ P/O 70-6122 Driven gear housing Ref.24 Fig.33

LUCAS 54483156/A
Bin B-2 (1/0/0)
Spring, ignition capacitor mounting
Ref# 2 Fig. 34 Page 75 #7 (1969) (Req:1)
Battery TR6C

A61
Bin D-9 (2/0/0)
Decal, Made in England
Ref# 34 Fig. 22 Page 53 #7 (1969) (Req:1)
Side panel?

GS127
Washer, plain
Ref# 25 Fig. 9 Page 29 #7 (1969) (Req:1)
Clutch lever assy

GS251
Piston
Ref# 15 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil release valve

GS254
Bin D-3 (2/0/0)
Washer, fiber
Ref# 17 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil release valve (beneath Cap 17/16)

GS308
Bin C-3 (4/2/2)
Washer, plain .390"Ix.622"Ox.06"T
Ref# 24 Fig. 13 Page 37 #7 (1969) (Req:2)
Rear shock absorber mount, upper nut
¹ #7 says 3 instead of 2

GS87
Breather disk
Ref# 2 Fig. 2 Page 15 #7 (1969) (Req:1)
Camshaft, inlet D.S.

N3
Spark plug 13mm-3/4"Reach; Gap .025" (.020 Maint/Repair 650/750 Twins)
Ref# 18 Fig. 35 Page 77 #7 (1969) (Req:2)
Cylinder head
Torque: 25 LBS
¹ Champ N3/N3C
NGK B7ES/B8ES Denso W24ESU

NA43A
Bin D-8 (4/0/0)
Joint Washer Paper washer
Ref# 30 Fig. 31 Page 71 #7 (1969) (Req:1)
Carburetter T120R
¹ '68 and earlier, use w E2968 Insul block & 244/1048 o-ring

NS191
Nipple
Ref# 17 Fig. 28 Page 65 #7 (1969) (Req:1)
Throttle cable T120R
Ref# 26 Fig. 28 Page 65 #7 (1969) (Req:3)
Handlebars T120R

NW100
Bin J-9 (2/3/0)
Grease nipple UNF (SAE) 1/4x28
Ref# 3 Fig. 13 Page 37 #7 (1969) (Req:1)
Swinging fork
¹ Grease@1,000 mi.intervals

PO172A
Nut, plain ASME 3/8-26TPI (Tool-3/8BS 5/16W)
Ref# 28 Fig. 14 Page 39 #7 (1969) (Req:3)
Brake pedal
¹ '65-'69 PO172; '70 99-0047; Best# PO172A.

PT104B
Washer, fiber
Ref# 5 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank drain

S1-51
Bin E-7 (2/0/0)
Nut (crankcase junction studs) CEI/BSC/Cycle 5/16-26TPI
Ref# 36 Fig. 2 Page 15 #7 (1969) (Req:8)
Crankcase

S1-52
Bin - (2/0/0)
Nut ASME 3/8-26TPI Thin (Tool-3/8BS 5/16W)
Ref# 26 Fig. 14 Page 39 #7 (1969) (Req:4)
Torque stay, head bolts 21/38 (bolts 2,3,4,5)
Ref# 34 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear brake cam lever
Torque: 20 LBS

S25-43
Washer, plain 1/4 x 1/2 x .0615"
Ref# 10 Fig. 6 Page 23 #7 (1969) (Req:1)
Auto advance unit bolt 23/9

S25-6
Bin C-1 (2/0/0)
Washer, plain 1/2"x1"x.100"
Ref# 17 Fig. 14 Page 39 #7 (1969) (Req:2)
Driver footrests (both)
¹ Interchangeable ~ 37-2027.
Ref# 33 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear brake cam lever
¹ Can use 37-2027.

S70-3
Ball, steel (1/4 in. dia.)
Ref# 42 Fig. 9 Page 29 #7 (1969) (Req:1)
Kickstarter pedal

S70-7
Oil pump valve ball (7/32 in. dia.)
Ref# 6 Fig. 3 Page 17 #7 (1969) (Req:2)
Oil pump

S79-2
Spoke nipple
Ref# 7 Fig. 19 Page 49 #7 (1969) (Req:40)
Front wheel
Ref# 6 Fig. 20 Page 51 #7 (1969) (Req:40)
Rear wheel

T24A
Kickstarter axle
Ref# 18 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover

WE2003
Rod
Ref# 29 Fig. 19 Page 49 #7 (1969) (Req:1)
Front brake cam

WF32
Bin I-6 (1/0/0)
Pin, pivot
Ref# 34 Fig. 19 Page 49 #7 (1969) (Req:2)
Front brake cam lever (rear)

WM3
Bolt, tire security
Ref# 45 Fig. 20 Page 51 #7 (1969) (Req:2)
Rear wheel

XA69
Tie, cable, metal
Ref# 39 Fig. 28 Page 65 #7 (1969) (Req:1)
Cable

1/16x3/8
Bin I-5 (0/0/0)
Pin, split (1/16 x 3/8 in.)
Ref# 40 Fig. 13 Page 37 #7 (1969) (Req:1)
Brake operating rod (rear)
¹ Also front brake operating rod (x 2)
Ref# 35 Fig. 19 Page 49 #7 (1969) (Req:2)
Front brake operating rod (front, both ends)

112201
Bin A-6 (3/0/0)
Bolt, pivot
Ref# 13 Fig. 36 Page 79 #7 (1969) (Req:2)
Headlight shell T120R-TR6R
Torque: 10 LBS

12/033
Washer, spring cupped
Ref# 25 Fig. 27 Page 63 #7 (1969) (Req:1)
Choke control spring washer

12/606
Cap
Ref# 24 Fig. 27 Page 63 #7 (1969) (Req:1)
Choke control cap

12/607
Bolt
Ref# 23 Fig. 27 Page 63 #7 (1969) (Req:1)
Choke control lever

127684
Screw
Ref# 29 Fig. 36 Page 79 #7 (1969) (Req:1)
Tail light/stop light assembly T120R-TR6R

137498
Bin A-6 (0/3/0)
Washer, plain .314"Ix3/4"Ox.61"T
Ref# 14 Fig. 36 Page 79 #7 (1969) (Req:2)
Headlight shell, pivot bolt 79/13 T120R-TR6R

14-
14-0101
Bin F-1 (3/2/0)
Bolt UNF (SAE) 1/4-28TPI X 7/16 U.H. (Tool-7/16)
Ref# 4 Fig. 11 Page 33 #7 (1969) (Req:2)
Primary chain oiler tube
Ref# 14 Fig. 25 Page 59 #7 (1969) (Req:4)
Seat hinge
Ref# 20 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, center stay
Ref# 20 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, front stay
Ref# 20 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender to frame

14-0102
Bin F-1 (1/3/3)
Bolt UNF (SAE) 1/4"X28TPI X 1/2" U.H.
Ref# 22 Fig. 25 Page 59 #7 (1969) (Req:4)
Seat rail
Ref# 31 Fig. 26 Page 61 #7 (1969) (Req:8)
?Fender
Ref# 31 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, bridge
Ref# 31 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, lift handle
Ref# 24 Fig. 35 Page 77 #7 (1969) (Req:2)
Ignition coil bracket to frame T120R-TR6C

14-0103
Bin F-1 (1/5/2)
Bolt UNF (SAE) 1/4-28TPI x 3/4 U.H.
Ref# 24 Fig. 23 Page 55 #7 (1969) (Req:2)
Battery holder front/rear straps
Ref# 22 Fig. 35 Page 77 #7 (1969) (Req:4)
Ignition coil bracket T120R-TR6C
Ref# 54 Fig. 35 Page 77 #7 (1969) (Req:6)
Horn relay bracket

14-0105
Bolt UNF (SAE) 1/4-28TPI X 15/16 U.H.
Ref# 34 Fig. 14 Page 39 #7 (1969) (Req:1)
Brake pedal stop

14-0113
Bin F-2 (9/1/1)
Bolt UNF (SAE) 5/16-24TPI X 9/16 U.H. (Tool-7/16)
Ref# 28 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard, front
¹ Substitute 82-4135 (shouldered) for easy lifting of guard
Ref# 32 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, bracket
Ref# 32 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, rear frame clip

14-0113/001
Bolt UNF (SAE) 5/16-24TPI X 9/16 U.H.
Ref# 47 Fig. 35 Page 77 #7 (1969) (Req:1)
Zener diode bracket
¹ Fastens bracket to middle lug

14-0114
Bin F-2 (5/0/0)
Bolt UNF (SAE) 5/16-24TPI X 3/4 U.H. (Tool-1/2)
Ref# 23 Fig. 15 Page 41 #7 (1969) (Req:2)
Muffler hanger (to muffler bracket), washer 41/24, nut 41/25

14-0115
Bin F-2 (3/0/0)
Bolt UNF (SAE) 5/16-24TPI X 7/8 U.H. (Tool-1/2)
Ref# 20 Fig. 15 Page 41 #7 (1969) (Req:4)
Muffler hanger (to frame), nut 41/21, washer 41/22
¹ #7 p61/Ref23 says 5/16" U.H.
But here it's 7/8"
Ref# 23 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender front and center stays to bracket (ref 5)
Ref# 23 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender rear stay to fork legs

14-0126
Bin F-2 (2/0/0)
Bolt UNF (SAE) 3/8-24TPI X 3/4 U.H.
Ref# 23 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine mount plates, top/rear

14-0201
Bin K-1 (1/0/0)
Bolt UNF (SAE) 1/4-28TPI X 1"U.H. (Tool-7/16")
Ref# 36 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearchange pedal

14-0204
Bolt UNF (SAE) 1/4-28TPI X 1-3/8 U.H.
Ref# 6 Fig. 15 Page 41 #7 (1969) (Req:4)
Exhaust crossover pipe clip

14-0218
Bin F-3 (1/4/2)
Bolt UNF (SAE) 5/16-24TPI X 1-5/16 U.H.
Ref# 30 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine torque stays
¹ #7 p45/Ref38 says 1-7/16"U.H. but here it's 1-5/16"
Ref# 38 Fig. 17 Page 45 #7 (1969) (Req:4)
Lower fork leg spindle
Torque: 25 LBS
¹ #7 p39/Ref30 says 1 5/16 U.H.

14-0219
Bin H-5 (2/0/0)
Bolt UNF (SAE) 5/16-24TPI X 1-1/2 U.H. (Tool-1/2)
Ref# 29 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust pipe/muffler clamp
Ref# 35 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust crossover pipe (Alternate)

14-0220
Bolt UNF (SAE) 5/16-24TPI X 1-3/4 U.H. (Tool-1/2)
Ref# 8 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine mount plate, D.S. top, front

14-0221
Bolt UNF (SAE) 5/16-24TPI X 2 U.H. (Tool-1/2)
Ref# 9 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine mount plate, T.S. top, front

14-0234
Bin F-4 (2/0/0)
Bolt UNF (SAE) 3/8-24TPI X 1-3/4 U.H. (Tool-9/16)
Ref# 24 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine mount plates, bottom, both sides
Orient: Head in, nut out

14-0235
Bin F-4 (4/0/0)
Bolt UNF (SAE) 3/8-24TPI X 1-7/8" U.H. (Tool-9/16)
Ref# 21 Fig. 13 Page 37 #7 (1969) (Req:4)
Shock mounts, top/bottom
Orient: Bolt heads in, nuts out

14-0251
Bolt UNF (SAE) 7/16-20TPI X 2-11/16 U.H.
Ref# 19 Fig. 12 Page 35 #7 (1969) (Req:2)
Main/rear frame bottom, front

14-0301
Bin E-1 (2/2/1)
Nut, plain UNF (SAE) 1/4-28TPI (Tool-11mm)
Ref# 15 Fig. 9 Page 29 #7 (1969) (Req:4)
Gearchange guideplate
Ref# 7 Fig. 15 Page 41 #7 (1969) (Req:4)
Exhaust crossover pipe clip
Ref# 25 Fig. 35 Page 77 #7 (1969) (Req:6)
Ignition coil bracket to frame T120R-TR6C
Ref# 56 Fig. 35 Page 77 #7 (1969) (Req:6)
Horn relay bracket

14-0302
Bin E-1 (6/2/0)
Nut, plain UNF (SAE) 5/16-24TPI (Tool-1/2)
Ref# 31 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover, bottom stud
Ref# 34 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard, stepped bolt 37/32
Ref# 12 Fig. 14 Page 39 #7 (1969) (Req:4)
Engine mount plates
Orient: Nuts out
¹ To 14-0220 bolts (Fig.14 Ref.8), D.S. Fore Top & Middle
Ref# 31 Fig. 14 Page 39 #7 (1969) (Req:2)
Torque stays
Ref# 21 Fig. 15 Page 41 #7 (1969) (Req:4)
Muffler hanger (to frame)
¹ Hanger-to-frame w washer Ref.22, and bolt Ref.20
Ref# 25 Fig. 15 Page 41 #7 (1969) (Req:2)
Muffler hanger
¹ Hanger-to-muffler-bracket w washer Ref.24 and bolt Ref.23
Ref# 27 Fig. 19 Page 49 #7 (1969) (Req:2)
Front brake cam spindle
Torque: 20 LBS
Ref# 28 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, rear frame clip
Ref# 19 Fig. 29 Page 67 #7 (1969) (Req:2)
Passenger footrest hanger

14-0303
Bin E-1 (9/1/1)
Nut, plain UNF (SAE) 3/8-24TPI (Tool-9/16)
Ref# 21 Fig. 2 Page 15 #7 (1969) (Req:2)
Crankcase junction stud TS (Ref.19)
Ref# 18 Fig. 12 Page 35 #7 (1969) (Req:2)
Main/rear frame (top)
Ref# 25 Fig. 13 Page 37 #7 (1969) (Req:4)
Rear shock absorber mount, top/bottom
Orient: Nuts out or it scrapes brake drum cover
Ref# 22 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine mount plate, bottom bolts both sides

14-0304
Bin E-1 (2/0/0)
Nut, plain UNF (SAE) 7/16-20TPI (Tool-7/16BS 3/8W)
Ref# 21 Fig. 12 Page 35 #7 (1969) (Req:2)
Main/rear frame, bottom front, bolt 35/19
Ref# 14 Fig. 13 Page 37 #7 (1969) (Req:2)
Torque stay, front (swingarm) and rear (brake plate)

14-0305
Nut, plain UNF (SAE) 1/2-20TPI (Tool-19mm(3/4") Socket)
Ref# 18 Fig. 14 Page 39 #7 (1969) (Req:2)
Driver footrests (both)

14-0401
Nut, locking UNF (SAE) 1/4-28TPI thin locking
Ref# 35 Fig. 14 Page 39 #7 (1969) (Req:1)
Brake pedal stop
Ref# 31 Fig. 19 Page 49 #7 (1969) (Req:1)
Front brake, threaded fork end

14-0402
Bin E-2 (1/3/1)
Nut, locking UNF (SAE) 5/16-24TPI thin locking
Ref# 24 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, center and front stays to bracket (R#5)
Orient: Nuts face out

14-0403
Bin E-2 (2/0/0)
Nut, locking UNF (SAE) 3/8-24TPI thin locking (Tool-9/16)
Ref# 18 Fig. 10 Page 31 #7 (1969) (Req:1)
Clutch adjuster pin
Ref# 27 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine mount plates, bolts 39/23, top/rear, both sides
Orient: Head in, nut out

14-0404
Bin P-2 (2/0/0)
Nut, locking UNF (SAE) 7/16-20TPI thin locking (Tool-11/16")
Ref# 9 Fig. 12 Page 35 #7 (1969) (Req:2)
Center stand '69/'70 650
¹ Goes with '69-'70 center stands (83-1267)

14-0701
Nut, locking UNF (SAE) 1/4-28TPI thin Philidas
Ref# 25 Fig. 23 Page 55 #7 (1969) (Req:2)
Battery holder straps, front/rear

14-0702
Bin E-3 (3/2/2)
Nut, locking UNF (SAE) 5/16-24TPI thin Philidas (Tool-13mm deep socket)
Ref# 23 Fig. 11 Page 33 #7 (1969) (Req:3)
Stator studs
Torque: 20 LBS
Ref# 31 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard, front mount
Ref# 29 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, bottom stay

14-0703
Bin E-3 (2/0/0)
Nut, locking UNF (SAE) 3/8-24TPI thin Philidas
Ref# 13 Fig. 12 Page 35 #7 (1969) (Req:1)
Side stand bolt F7021
Orient: Nut faces out

14-1201
Bin E-4 (11/0/0)
Nut, locking UNF (SAE) 1/4-28TPI Cleveloc (Tool-9/16)
Ref# 22 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, center stay to fender
Ref# 22 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, front stay to fender
Ref# 22 Fig. 26 Page 61 #7 (1969) (Req:1)
Front fender, rear stay to fender
Ref# 22 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, liscense plate bracket
Ref# 22 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, bridge
Ref# 22 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, lifting handle
Ref# 22 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender, frame bracket, top

14-1301
Bin M-5 (2/1/0)
Nut, locking UNF (SAE) 1/4-28TPI thin Cleveloc
Ref# 52 Fig. 2 Page 15 #7 (1969) (Req:1)
Protection blade
Ref# 33 Fig. 31 Page 71 #7 (1969) (Req:4)
Carburetter adaptor 21/12, 21/13 (mount stud) T120R
¹ RPC #7 incorrectly lists part number S1932 (21-1932)

14-1302
Bin E-5 (4/1/1)
Nut, locking UNF (SAE) 5/16-24TPI thin Cleveloc
Ref# 36 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust crossover pipe
Ref# 25 Fig. 22 Page 53 #7 (1969) (Req:2)
Gas tank, front tank mount

14-1303
Nut, locking UNF (SAE) 3/8-24TPI thin Cleveloc (Tool-9/16)
Ref# 6 Fig. 17 Page 45 #7 (1969) (Req:2)
Stanchion tube pinch bolt 45/4
Torque: 25 LBS

14-1427
Stud, gearbox inner cover UNC/UNF (5/16-18TPI)(5/16-24TPI) X 3"O.A.
Ref# 1 Fig. 7 Page 25 #7 (1969) (Req:2)
Gearbox
¹ Coarse thread to case.

14-1445
Stud, TS crankcase junction UNC/UNF 3/8-16TPI/24TPI X 4-1/2 O.A.
Ref# 19 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase
Torque: 20 LBS
¹ Crankcase junction stud #7

14-1902
Nut, locking UNF (SAE) 5/16-24TPI thin Aerotite (Tool-1/2)
Ref# 43 Fig. 20 Page 51 #7 (1969) (Req:2)
Rear wheel chain adjuster

14-1903
Bin I-1 (2/2/0)
Nut, locking UNF (SAE) 3/8-24TPI thin Aerotite (Tool-9/16)
Ref# 20 Fig. 18 Page 47 #7 (1969) (Req:2)
Handlebar mount T120R-TR6R
¹ Dummy notes line one

14-6101
Bin L-7 (2/0/0)
Bolt (chaincase oil level plug) UNC (SAE) 1/4-20TPI X 1/2
Ref# 39 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase level plug

14-6102/001
Bolt 1/4-20TPI X 5/8
Ref# 46 Fig. 35 Page 77 #7 (1969) (Req:1)
Zener diode heat sink
¹ Fastens heat sink to bracket

14-6220
Bolt (crankcase junction, upper rear DS) UNC (SAE) 5/16-18TPI X 1-3/4 U.H.
Ref# 31 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase D.S.

14-6242
Bolt (TS crankcase junction) UNC (SAE) 3/8-16TPI X 4"U.H.
Ref# 49 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase
Torque: 13 LBS

14-6608
Bin K-8 (14/0/0)
Screw, Posidrive UNC (SAE) 1/4-20TPI X 1" U.H. (Tool-Posidrive)
Ref# 8  Fig.  6 Page 23 #7 (1969) (Req:5)
Timing cover
¹ 10/11/1/2/3 O'clock from patent plate are 1-3/8"O.A.
Ref# 22 Fig.  7 Page 25 #7 (1969) (Req:1)
Gearbox inner cover
Ref# 34 Fig.  9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover
Orient: Rear-most screw
Ref# 34 Fig. 11 Page 33 #7 (1969) (Req:6)
Primary chaincase cover

14-6609
Bin - (5/0/0)
Screw, Posidrive UNC (SAE) 1/4"-20TPI X 1-5/16" U.H. (Tool-Posidrive)
Ref# 7 Fig. 6 Page 23 #7 (1969) (Req:3)
Timing cover
¹ 5/7o'clock: 1-27/64"O.A.;9 o'clock: 1-1/8"O.A.
Ref# 33 Fig. 9 Page 29 #7 (1969) (Req:2)
Gearbox outer cover

14-6620
Bin - (2/0/0)
Screw, Posidrive UNC (SAE) 5/16-18TPI X 29/32 (7/8) U.H. (Tool-Posidrive)
Ref# 35 Fig. 11 Page 33 #7 (1969) (Req:2)
Primary chaincase cover

14-7023
Screw, Allen UNC (SAE) 5/16-18TPI X 1 3/4" U.H. (Tool-7/64" hex)
Ref# 23 Fig. 7 Page 25 #7 (1969) (Req:1)
Gearbox inner cover

144921
Bin A-6 (1/0/0)
Screw
Ref# 24 Fig. 36 Page 79 #7 (1969) (Req:2)
Tail light/stop light lens T120R-TR6R
Ref# 5 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell, fixing plate 79/6 T120R-TR6R

199001
Grommet, rubber
Ref# 19 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender, stoplight lead

21-
21-0541 / S541
Bolt UNF (SAE) 5/16-24TPI x 1-1/8 (Tool-1/2")
Ref# 43 Fig. 9 Page 29 #7 (1969) (Req:1)
Kickstarter pedal

21-0543 / S543
Plug UNF (SAE) 1/4-28TPI x 5/16 (Tool-7/16)
Ref# 42 Fig. 2 Page 15 #7 (1969) (Req:1)
Gearbox level plug

21-0544 / S544
Bin K-8 (1/0/0)
Nut, domed UNF (SAE) 5/16-24TPI (Tool-1/2")
Ref# 46 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover, upper stud
Ref# 36 Fig. 11 Page 33 #7 (1969) (Req:2)
Primary chaincase cover (stator studs)
Torque: 10 LBS

21-0545 / S545
Nut UNC (SAE) 9/16-12TPI (Tool-15/16)
Ref# 10 Fig. 13 Page 37 #7 (1969) (Req:1)
Swinging fork, bolt 37/8
Torque: 45 LBS

21-0547 / S547
Stud, gearbox outer cover UNC/UNF 1/4-20TPI/28TPI X 7/8 O.A.
Ref# 5 Fig. 9 Page 29 #7 (1969) (Req:4)
Clutch lever assembly

21-0548 / S548
Stud, engine mounting plate UNF (SAE) 7/16-20TPI X 1-3/8 O.A.
Ref# 21 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine mount plates

21-0578 / S578
Bin I-2 (2/0/0)
Grub screw ASME 1/4
Ref# 12 Fig. 17 Page 45 #7 (1969) (Req:1)
Upper yoke
¹ Secures frame lock cylinder

21-0586 / S586
Bin L-5 (1/1/0)
Nut, locking UNF (SAE) 9/16-18TPI -Locktite 243 (blue) (Tool-Lock-plate & 7/8")
Ref# 1 Fig. 10 Page 31 #7 (1969) (Req:1)
Clutch securing nut
Torque: 50 LBS
¹ Renew after removing

21-0588 / S588
Bolt UNC (SAE) 7/16-20TPI X 1-3/16 U.H. (Tool-5/8)
Ref# 23 Fig. 12 Page 35 #7 (1969) (Req:2)
Rear/main frame, bottom rear

21-0589 / S589
Bolt UNF (SAE) 5/16-24TPI X 1-1/8 U.H. (Tool-1/2)
Ref# 18 Fig. 18 Page 47 #7 (1969) (Req:2)
Handlebar mount T120R-TR6R

21-0590 / S590
Bin B-9 (1/1/1)
Bolt UNF (SAE) 1/4-28TPI X 1-3/16 U.H.
Ref# 8 Fig. 33 Page 73 #7 (1969) (Req:2)
Instrument mounting bracket

21-0594 / S594
Bin K-3 (1/2/0)
Nut UNF (SAE) 9/16-18TPI Thin (Tool-15/16")
Ref# 26 Fig. 8 Page 27 #7 (1969) (Req:1)
Kickstarter ratchet
Torque: 45 LBS
¹ Blue Loctite

21-0620 / S620
Bolt UNF (SAE) 9/16-18TPI X (8-5/8 U.H.)(9-1/4) (Tool-7/8)
Ref# 8 Fig. 13 Page 37 #7 (1969) (Req:1)
Swinging fork
Torque: 45 LBS
Orient: Bolt head to T.S.

21-0650 / S650
Screw, taptite
Ref# 38 Fig. 19 Page 49 #7 (1969) (Req:3)
Front brake air scoop

21-0672 / S672
Nut UNF (SAE) 5/16-24TPI
Ref# 6 Fig. 28 Page 65 #7 (1969) (Req:1)
Clutch cable

21-0684 / S684
Bin I-1 (1/0/0)
Bolt, pinch UNF (SAE) 3/8-24TPI X 1-11/16 U.H.
Ref# 15 Fig. 17 Page 45 #7 (1969) (Req:1)
Upper yoke
Torque: 15 LBS

21-0685 / S685
Bin I-2 (1/0/0)
Nut, seated UNF (SAE) 3/8-24TPI
Ref# 16 Fig. 17 Page 45 #7 (1969) (Req:1)
Upper yoke pinch bolt
Torque: 15 LBS

21-0692 / S692
Bin 0-2 (0/8/8)
Nut UNF (SAE) 3/8-24TPI 12 points
Ref# 3 Fig. 5 Page 21 #7 (1969) (Req:8)
Cylinder block base
Torque: 35 LBS

21-1800 / S1800
Stud, driver footrests UNF (SAE) 1/2-20TPI X 1-9/16 O.A.
Ref# 16 Fig. 14 Page 39 #7 (1969) (Req:2)
Driver footrests

21-1801 / S1801
Stud, frame to rear loop UNF (SAE) 3/8-24TPI X 3-7/8 O.A.
Ref# 16 Fig. 12 Page 35 #7 (1969) (Req:1)
Main/rear frame (top)

21-1802 / S1802
Bolt UNF (SAE) 7/16-20TPI X 27/32 U.H.
Ref# 12 Fig. 13 Page 37 #7 (1969) (Req:1)
Swinging fork to frame

21-1822 / S1822
Bolt UNF (SAE) 5/16-24TPI X 1/2 U.H.
Ref# 37 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank mount, lower
Ref# 25 Fig. 26 Page 61 #7 (1969) (Req:1)
Front fender to bottom stay (R#4)
Ref# 25 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, bracket (R#5) to fork legs

21-1863 / S1863
Stud, oil junction block BSPP 5/16-?TPI X 1-1/2 O.A.
Ref# 27 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase

21-1864 / S1864
Stud, oil pump BSW/BSF 1/4-20TPI/26TPI X 1-5/16
Ref# 10 Fig. 3 Page 17 #7 (1969) (Req:2)
Oil pump body

21-1865 / S1865
Stud, cylinder block UNC (SAE) 3/8"-16TPI X 1-7/8" O.A.)(3/16"-7/32"-24TPI X 1-3/4" O.A.
Ref# 28 Fig. 2 Page 15 #7 (1969) (Req:8)
Crankcase to cylinder block
¹ Crankcase, 16TPI; Nut, 24TPI.

21-1866 / S1866
Stud, alternator stator UNC/UNF OR BSW 5/16-18TPI/24TPI X 4-11/32 O.A.
Ref# 16 Fig. 11 Page 33 #7 (1969) (Req:2)
Stator stud (forward, top and bottom)

21-1867 / S1867
Stud, alternator stator UNC/UNF OR BSW 5/16-18TPI/24TPI
Ref# 17 Fig. 11 Page 33 #7 (1969) (Req:1)
Stator stud, aft

21-1869 / S1869
Bolt (crankcase junction, upper middle DS) UNF (SAE) 5/16-24TPI X 1-7/8 U.H.
Ref# 32 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase D.S.

21-1870 / S1870
Bolt (crankcase junction, upper forward DS) UNC (SAE) 5/16-18TPI X 2-1/2 U.H.
Ref# 30 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase D.S.

21-1871 / S1871
Tachometer drive plug LEFT-HAND
Ref# 25 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase D.S. tach drive

21-1872 / S1872
Plug UNC (SAE) 1/2-13TPI
Ref# 29 Fig. 2 Page 15 #7 (1969) (Req:1)
Timing hole plug (crankcase)

21-1873 / S1873
Bin N-2 (0/2/0)
Screw UNC (SAE) 1/4"-20TPI X 13/16" U.H.
Ref# 18 Fig. 2 Page 15 #7 (1969) (Req:2)
Crankcase junction
¹ Ref.17, hollow dowel shown in #7 not used in 1969

21-1875 / S1875
Bin 0-3 (1/1/1)
Bolt UNC (SAE) 1/4-20TPI X 2-5/32 U.H. (Tool-3/16W 1/4BS)
Ref# 36 Fig. 5 Page 21 #7 (1969) (Req:4)
Rocker box
Torque: 5 LBS

21-1878 / S1878
Screw, Posidrive UNC (SAE) 1/4-20TPI X 2 3/4 U.H. (Tool-Posidrive)
Ref# 32 Fig. 9 Page 29 #7 (1969) (Req:2)
Gearbox outer cover
Orient: Top & bottom screws (match case locators)
¹ Fig 9 is wrong/confusing.

21-1879 / S1879
Screw, countersunk UNC (SAE) 1/4-20TPI X 13/32 O.A. Slotted
Ref# 27 Fig. 9 Page 29 #7 (1969) (Req:2)
Clutch lever assy

21-1883 / S1883
Stud, shouldered UNF (SAE) 5/16-24TPI
Ref# 24 Fig. 22 Page 53 #7 (1969) (Req:2)
Gas tank front mount

21-1906 / S1906
Bin - (2/0/0)
Nut, conical UNF (SAE) 1/4-28TPI
Ref# 12 Fig. 3 Page 17 #7 (1969) (Req:2)
Oil pump
Torque: 5 LBS

21-1907 / S1907
Bolt UNC (SAE) 5/16-18TPI X 1-1/8" U.H. (Tool-7/16")
Ref# 20 Fig. 7 Page 25 #7 (1969) (Req:1)
Gearbox inner cover

21-1908 / S1908
Bin H-5 (3/0/0)
Nut, plain UNF (SAE) 5/16-24TPI tall 7/16AF (Tool-1/2)
Ref# 31 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust pipe to muffler clamp, bolt 41/29

21-1910 / S1910
Bolt UNF (SAE) 3/8-24TPI X 13/16 U.H. Full thread
Ref# 16 Fig. 29 Page 67 #7 (1969) (Req:2)
Passenger footrest hanger

21-1932 / S1932
Nut, locking
Ref# 16 Fig. 5 Page 21 #7 (1969) (Req:2)
Carburetter adaptor/Cylinder head
¹ E4608(BSC 20) in #7:up to'68. Use 21-1932(UNF 16tpi) 1969-on

21-1978 / S1978
Bin P-2 (4/1/1)
Bolt, pivot UNF (SAE) 7/16" x 20 (Tool-9/16")
Ref# 7 Fig. 12 Page 35 #7 (1969) (Req:2)
Center stand '69/'70 650
¹ Goes with '69-'70 center stands (83-1267)

21-2016 / S549
Bin S-M (0/4/0)
Nut, locking UNF (SAE) 5/16-24TPI
Ref# 11 Fig. 1 Page 13 #7 (1969) (Req:4)
Con rod
Torque: 28 LBS

3/32x1/2
Pin, split
Ref# 19 Fig. 25 Page 59 #7 (1969) (Req:1)
Seat latch

30-
30-276-037-11
Bin B-9 (4/0/0)
Nut
Ref# 7 Fig. 33 Page 73 #7 (1969) (Req:4)
Speedo/tach mount

30-282-014-11
Bin B-9 (3/0/0)
Washer
Ref# 6 Fig. 33 Page 73 #7 (1969) (Req:4)
Speedo/tach mount

31-
31-315-135
Brass fitting
Ref# - Fig. 33 Page 73 #7 (1969) (Req:1)
Speedo connection

31-371-398
Bin - (0/1/0)
Spade
Ref# 31 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach cable T120R-TR6R

37-
37-0135 / W135
Bin I-7 (2/2/0)
Spring, return
Ref# 24 Fig. 19 Page 49 #7 (1969) (Req:2)
Front brake shoe
Ref# 30 Fig. 20 Page 51 #7 (1969) (Req:2)
Rear brake shoe

37-0582 / W582
Retaining ring LEFT-HAND (Tool-Z76)
Ref# 15 Fig. 19 Page 49 #7 (1969) (Req:1)
Front wheel bearing, T.S.

37-0653 / W653
Bearing, wheel (front) 20 x 47 x 14 mm (Ball Journal)
Ref# 10 Fig. 19 Page 49 #7 (1969) (Req:2)
Front wheel
¹ Use sealed or grease @12,000mi
Ref# 18 Fig. 20 Page 51 #7 (1969) (Req:2)
Rear wheel
¹ Grease @ 12,000 miles.

37-1007 / W1007
Rim (WM3 18)
Ref# 3 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel

37-1015 / W1015
Plate
Ref# 42 Fig. 20 Page 51 #7 (1969) (Req:2)
Chain adjuster end plate

37-1021 / W1021
Retaining ring (Tool-Z76)
Ref# 19 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel bearing D.S.

37-1022 / W1022
Backing ring Flat ring; .067"Thick; 1.5"ID
Ref# 17 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel D.S.

37-1024 / W1024
Distance piece Stepped
Ref# 22 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel
Orient: Small end to hub

37-1083 / W1083
Bin I-8 (1/0/0)
Brake cam
Ref# 31 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear brake

37-1090 / W1090
Bin I-7 (0/1/0)
Spring, return
Ref# 35 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear brake cam lever

37-1107 / W1107
Spoke (8/10G X 7 9/16 in. 90 Degrees)
Ref# 4 Fig. 20 Page 51 #7 (1969) (Req:10)
Rear wheel

37-1108 / W1108
Spoke (8/10G X 7 7/8 in. 90 Degrees)
Ref# 5 Fig. 20 Page 51 #7 (1969) (Req:20)
Rear wheel

37-1112 / W1112
Anchor plate
Ref# 23 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear brake

37-1197 / W1197
Weight, balancing (1/2 oz)
Ref# 17 Fig. 19 Page 49 #7 (1969)
Front wheel

37-1198 / W1198
Weight, balancing (1 oz)
Ref# 18 Fig. 19 Page 49 #7 (1969)
Front wheel

37-1230 / W1230
Rim (WM2 19)
Ref# 3 Fig. 19 Page 49 #7 (1969) (Req:1)
Front wheel

37-1237 / W1237
Bin I-3 (0/1/1)
Dust cover Cupped(.215"Deep); Inside lip .235"High; .79-.82"ID
Ref# 11 Fig. 19 Page 49 #7 (1969) (Req:1)
Bearing, front wheel
Orient: Cup to bearing

37-1278 / W1278
Distance tube
Ref# 21 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel

37-1280 / W1280
Washer, plain 5/8"
Ref# 40 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel T.S.

37-1281 / W1281
Spindle
Ref# 14 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel
Orient: Shoulder to T.S.

37-1328 / W1328
Spoke (8/10G x 5 5/8 in. straight)
Ref# 4 Fig. 19 Page 49 #7 (1969) (Req:20)
Front wheel

37-1406 / W1406
Brake shoe, leading (with lining)
Ref# 25 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear brake
Orient: See p50 #7
For correct lead/trail orientation

37-1407 / W1407
Brake shoe, trailing (with lining)
Ref# 26 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear brake
Orient: See page 50 #7 for correct leading/trailing orientation.

37-1415 / W1415
Bin I-9 (2/2/0)
Thrust pad
Ref# 29 Fig. 20 Page 51 #7 (1969) (Req:2)
Rear brake

37-1467 / W1467
Pin, pivot
Ref# 47 Fig. 20 Page 51 #7 (1969) (Req:1)
Brake cam lever

37-1472 / W1472
Hub
Ref# 7 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel

37-1474 / W1474
Bin I-4 (4/0/0)
Grease retainer Flat; .018"Thick; 1.06"ID
Ref# 15 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel D.S.

37-1476 / W1476
Speedometer adaptor LEFT HAND
Ref# 37 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel

37-1477 / W1477
Bin I-4 (1/0/0)
Distance piece Straight, length: 1.055 to 1.060" (John Healy)
Ref# 38 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel, timing side
¹ Bonnie's original part 1.042"; new part is 1.048"

37-1481 / W1481
Grease retainer Cupped, tapered to center; .205"Deep; .885"ID
Ref# 14 Fig. 19 Page 49 #7 (1969) (Req:1)
Front wheel bearing, D.S.
Orient: Cup to bearing

37-1486 / W1486
RIM, SPOKES, AND HUB ASSEMBLY
Ref# 2 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel

37-1498 / W1498
Brake drum
Ref# 11 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear brake

37-1499 / W1499
Sprocket
Ref# 8 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel (46T)

37-1500 / W1500
Bin F-5 (0/4/4)
Bolt BSF 1/4-26TPI X 13/16 U.H.
Ref# 9 Fig. 20 Page 51 #7 (1969) (Req:8)
Rear wheel sprocket to brake drum

37-1635 / W1635
Bin I-4 (0/1/1)
Grease retainer Flat.019"Thick; Inside step.125"Wide x.035"High; 1.123"ID
Ref# 36 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel, outside T.S. bearing

37-1654 / W1654
Bin - (1/0/1)
Grease retainer Cupped(.283"Deep); Inside lip.08"High; 1.025ID
Ref# 16 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel T.S.
Orient: Cup to bearing

37-1690 / W1690
Bolt CEI/BSC/Cycle 5/16-26TPI X 11/16 U.H.
Ref# 12 Fig. 20 Page 51 #7 (1969) (Req:8)
Wheel breakdrum to hub

37-1691 / W1691
Nut, locking ASME 5/16-26TPI
Ref# 13 Fig. 20 Page 51 #7 (1969) (Req:8)
Brakedrum to hub

37-1708 / W1708
Spoke (8/10G x 4 25/32 in. 78)
Ref# 5 Fig. 19 Page 49 #7 (1969) (Req:10)
Front wheel

37-1709 / W1709
Spoke (8/10G x 4 7/8 in. 100)
Ref# 6 Fig. 19 Page 49 #7 (1969) (Req:10)
Front wheel

37-1710 / W1710
Locking screw, Allen BA 2BA x 1/4 x 5/16 U.H.
Ref# 20 Fig. 20 Page 51 #7 (1969) (Req:1)
Retaining ring

37-1721 / W1721
RIM SPOKES AND HUB ASSEMBLY
Ref# 2 Fig. 19 Page 49 #7 (1969) (Req:1)
Front wheel

37-1722 / W1722
Hub and brake drum
Ref# 8 Fig. 19 Page 49 #7 (1969) (Req:1)
Front wheel

37-1991 / W1991
Screen, anchor plate
Ref# 37 Fig. 19 Page 49 #7 (1969) (Req:1)
Front brake air scoop

37-1996 / W1996
Brake shoe with Lining
Ref# 20 Fig. 19 Page 49 #7 (1969) (Req:2)
Front brake

37-2001 / W2001
Cam, brake operating
Ref# 25 Fig. 19 Page 49 #7 (1969) (Req:2)
Front brake

37-2005 / W2005
Fork end, threaded
Ref# 30 Fig. 19 Page 49 #7 (1969) (Req:1)
Front brake cam rod

37-2006 / W2006
Bin I-6 (1/0/0)
Pin, pivot
Ref# 13 Fig. 28 Page 65 #7 (1969) (Req:1)
Front brake (spring_fix)

37-2015 / W2015
Brake cam lever
Ref# 32 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear brake

37-2026 / W2026
Bin I-6 (2/0/0)
Abutment
Ref# 23 Fig. 19 Page 49 #7 (1969) (Req:2)
Front brake shoe pad

37-2027 / W2027
Bin I-6 (2/0/0)
Washer, plain 1/2"x1"x.100"
Ref# 36 Fig. 19 Page 49 #7 (1969) (Req:2)
Front brake cam lever
¹ Interchangeable ~ S25-6.

37-2057 / W2057
Spindle
Ref# 9 Fig. 19 Page 49 #7 (1969) (Req:1)
Front wheel

37-2058 / W2058
Nut 3/4"
Ref# 33 Fig. 19 Page 49 #7 (1969) (Req:1)
Front brake anchor plate

37-2089 / W2089
Chain adjuster
Ref# 41 Fig. 20 Page 51 #7 (1969) (Req:2)
Rear wheel

37-2102 / W2102
WHEEL, COMPLETE
Ref# 1 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel

37-3337 / W3337
Bin I-3 (1/1/1)
Support ring Stepped: 1.844"OD, 1.071"ID, .166"Thick (Step .68")
Ref# 13 Fig. 19 Page 49 #7 (1969) (Req:1)
Bearing, front wheel

37-3402 / W3402
Spoke (8/10G X 7-9/16" 110 Deg.)
Ref# 4A Fig. 20 Page 51 #7 (1969) (Req:10)
Rear wheel

37-3425 / W3425
Nut UNF (SAE) Thickness: 3/4"(.470")(15/32"); Flats: 1.306" (1-5/16")
Ref# 46 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel spindle, D.S. (inside)
¹ Inside nut, D.S.

37-3426 / W3426
Nut UNF (SAE) Thickness: 3/4"(.322"); Flats: 1.317"(<1-5/16")
Ref# 24 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel spindle, T.S. (inside)
¹ Inside nut, T.S.

37-3453 / W3453
Cam lever
Ref# 26 Fig. 19 Page 49 #7 (1969) (Req:1)
Front brake (rear lever)

37-3454 / W3454
Cam lever
Ref# 28 Fig. 19 Page 49 #7 (1969) (Req:1)
Front brake (front lever)

37-3458 / W3458
WHEEL COMPLETE
Ref# 1 Fig. 19 Page 49 #7 (1969) (Req:1)
Front wheel

37-3460 / W3460
Cover
Ref# 16 Fig. 19 Page 49 #7 (1969) (Req:1)
Front wheel

37-3462 / W3462
Anchor plate
Ref# 19 Fig. 19 Page 49 #7 (1969) (Req:1)
Front brake

37-3522 / W3522
Spring, return
Ref# 32 Fig. 19 Page 49 #7 (1969) (Req:1)
Front brake lever

41-
41-148-203-10
Shaft, trip control
Ref# 9 Fig. 33 Page 73 #7 (1969) (Req:1)
Speedometer

5/64x1 3/8
Bin K-2 (6/2/0)
Pin, split - inner quadrant (5/64" X 1 3/8")
Ref# 19 Fig. 7 Page 25 #7 (1969) (Req:2)
Gear selectors

5/64x1/2
Pin, split (5/64" X 1/2")
Ref# 26 Fig. 9 Page 29 #7 (1969) (Req:1)
Clutch lever assembly

54130041
Nut
Ref# 31 Fig. 36 Page 79 #7 (1969) (Req:1)
Ignition switch T120R-TR6R

54190042
Cover, insulated
Ref# 13 Fig. 35 Page 77 #7 (1969)
Lucar connector, ignition coil
¹ Use B-Wiring C233
Spade terminal cover 1/4" right angle

54190108 LUCAS 54190108
Bin B-6 (6/0/0)
Spade terminal, male 1/4" male, double 90 degrees
Ref# 3 Fig. 35 Page 77 #7 (1969) (Req:4)
Ignition Coil
¹ Similar to British Wiring C200 (straight)

54523508
Shell
Ref# 1 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell T120R-TR6R

54938986
Bin A-2 (2/0/0)
Fuse assembly
Ref# 11 Fig. 24 Page 57 #7 (1969) (Req:1)
Battery
¹ Use slowblow 17A continuous
(Marked 35A instantaneous)

54942078 LUCAS 54942078
Lucar connector Female
Ref# 12 Fig. 35 Page 77 #7 (1969)
Ignition coil
¹ Use B-Wiring C232
Spade terminal right angle 1/4"

57-
57-0023 / T23
Bin - (0/1/0)
Bush BoreD 0.751-0.752 Clearance .003-.005 Spring Len 1/2"
Ref# 2 Fig. 9 Page 29 #7 (1969) (Req:1)
Kickstarter spindle bush
¹ #7 reverses Ref# for 57-0043 & 57-0023

57-0031 / T31
Kickstarter return spring
Ref# 17 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover

57-0045 / T45
Kickstart stop
Ref# 16 Fig. 7 Page 25 #7 (1969) (Req:1)
Gearbox inner cover

57-0047 / T47
Anchor pin
Ref# 4 Fig. 9 Page 29 #7 (1969) (Req:1)
Kickstarter spring

57-0057 / T57
Bin - (0/2/0)
Bush BoreD 0.7495-.7505" Shaft clearance .0005-.0025"
Ref# 3 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearchange quadrant (outer bush)
¹ #7 reverses Ref# for 57-0057 & 57-0023

57-0280 / T280
Bin K-6 (3/0/0)
Circlip
Ref# 19 Fig. 8 Page 27 #7 (1969) (Req:1)
Mainshaft bearing
Ref# 12 Fig. 19 Page 49 #7 (1969) (Req:1)
Bearing, front wheel
¹ Same on mainshaft bearing

57-0291 / T291
Selector fork rod
Ref# 10 Fig. 7 Page 25 #7 (1969) (Req:1)
Gear selectors

57-0394 / T394
Bin L-3 (6/0/0)
Rollers Dia-.2495/.2500"; Length-.231/.236"
Ref# 4 Fig. 10 Page 31 #7 (1969) (Req:20)
Clutch hub

57-0397 / T397
Bin K-2 (0/1/1)
Quadrant
Ref# 17 Fig. 7 Page 25 #7 (1969) (Req:1)
Gear selectors
Orient: Wider pivot boss goes towards gear side
¹ Split pin forward

57-0404 / T404
Bin K-1 (0/4/0)
Spring, quadrant return Curved; Free length: 1 3/4"; Coils: 12
Ref# 10 Fig. 9 Page 29 #7 (1969) (Req:2)
Gearchange quadrant

57-0405 / T405
Bin K-1 (0/4/0)
Spring, plunger Free len: 1 1/4"; Coils: 12
Ref# 12 Fig. 9 Page 29 #7 (1969) (Req:2)
Gearchange quadrant plunger
¹ Like new

57-0406 / T406
Bin K-1 (3/2/2)
Plunger, gearchange quadrant OD 0.4315-.4320" Bore clearance 0.0005-.0015"
Ref# 11 Fig. 9 Page 29 #7 (1969) (Req:2)
Gearchange quadrant
Orient: Single bevel to guide plate
¹ Height: Orig.936-.937"; MAPCycle.901-.902"; New unused.860"

57-0407 / T407
Bin K-1 (0/1/1)
Guide plate
Ref# 13 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearchange plunger assembly
Orient: Beveled edges face away from center
¹ Original part

57-0408 / T408/9
Bin - (0/0/1)
Gearchange quadrant
Ref# 8 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover

57-0412 / T412
Bush BoreD 0.6245-.6255" Shaft clearance 0.0007-.0032"
Ref# 15 Fig. 7 Page 25 #7 (1969) (Req:1)
Gearchange quadrant (inner bush)

57-0423A / T423A
Pin, screwed (1 27/32 in. U.H.)
Ref# 13 Fig. 10 Page 31 #7 (1969) (Req:3)
Inner plate
¹ Use 57-4754 (Bax: 1-13/16"UH)

57-0440 / T440
Bin K9-S3 (2/4/0)
Nut CEI/BSC/Cycle 1 1/4" (Tool-Z63)
Ref# 14 Fig. 8 Page 27 #7 (1969) (Req:1)
Mainshaft, gearbox sprocket
Torque: 50 LBS
¹ Blue Loctite. Remove w. air wrench.

57-0448 / T448
Bin - (0/1/0)
Bearing, mainshaft (D.S.) 1-1/4" x 2-1/2" x 5/8" Ball Journal (Tool-Z15 2-1/2" drift)
Ref# 15 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox casing
¹ WS MANUAL 63-70 P.D9

57-0730 / T730
Kickstarter pinion
Ref# 23 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox outer cover

57-0731 / T731
Kickstarter ratchet
Ref# 24 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox outer cover

57-0912 / T912
Bin K-7 (1/0/0)
Locating peg Dia:.07-.074" Length:.3135"(2).2585"/6.57mm(1)
Ref# 13 Fig. 2 Page 15 #7 (1969) (Req:1)
Layshaft thrust washer
¹ #7 calls for 1, 2 are required

57-0913 / T913
Selector fork Shorter barrel than 57-2608, main shaft selector
Ref# 8 Fig. 7 Page 25 #7 (1969) (Req:1)
Layshaft

57-0916 / T916
Mainshaft second gear (20T)
Ref# 6 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox

57-0926 / T926
Layshaft low gear (30T) BUSH bore dia:0.8135-.8145" BUSH clearance:0.0025-.0045"
Ref# 7 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox

57-0928 / T928
Bin K-4 (1/1/0)
Bush BoreD 0.8135-.8145" Shaft clearance 0.0025-45"
Ref# 8 Fig. 8 Page 27 #7 (1969) (Req:1)
Layshaft low gear

57-0946 / T946
Bin K-5 (0/0/0)
Oil seal OD: 2.500
Ref# 17 Fig. 8 Page 27 #7 (1969) (Req:1)
High gear bearing
Orient: Open lip/springs face gearbox

57-0989 / T989
Hollow dowel - timing cover oil feed
Ref# 12 Fig.  2 Page 15 #7 (1969) (Req:2)
Crankcase/Timing cover
Ref# 6  Fig.  6 Page 23 #7 (1969) (Req:2)
Timing cover
¹ Qty is (2), not (1) as in #7. Same as Ref.12/Fig.2
Ref# 2  Fig.  7 Page 25 #7 (1969) (Req:4)
Gearbox inner cover

57-1040 / T1040
Bin L-4 (6/5/0)
Screw, countersunk BA 1BA x 9/16 x 0.417" U.H.
Ref# 8 Fig. 10 Page 31 #7 (1969) (Req:6)
Inner & Outer clutch center plates

57-1065 / T1065
Layshaft second gear (26T)
Ref# 9 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox

57-1076 / T1076
Bin A-3 (2/2/0)
Screw 3/8 U.H.
Ref# 43 Fig. 13 Page 37 #7 (1969) (Req:2)
Chainguard, brakelight switch
Ref# 43 Fig. 13 Page 37 #7 (1969) (Req:1)
Brakelight switch lever

57-1167 / T1167
Spring, Kickstarter
Ref# 41 Fig. 9 Page 29 #7 (1969) (Req:1)
Kickstarter pedal assembly

57-1222 / T1222
Bin K-3 (1/0/0)
Pin; nut; washer Comes with nut, washer
Ref# 45 Fig. 9 Page 29 #7 (1969) (Req:1)
Kickstarter lever
Orient: Nut must face forward for clearance with footrest
¹ One Ref# for all

57-1250 / T1250
Bin - (0/1/0)
Spring Free length 1/2 in.
Ref# 22 Fig. 8 Page 27 #7 (1969) (Req:1)
Mainshaft, kickstarter pinion

57-1257 / T1257
Bin D-3 (4/0/0)
Washer, fiber 15/32 x 7/8
Ref# 41 Fig. 2 Page 15 #7 (1969) (Req:1)
Gearbox drain/level plug

57-1272 / T1272
Kickstarter pedal
Ref# 40 Fig. 9 Page 29 #7 (1969) (Req:1)
Kickstarter assembly

57-1362 / T1362
Plate, clutch, driving (bonded)
Ref# 14 Fig. 10 Page 31 #7 (1969) (Req:6)
Clutch sprocket and housing unit
¹ Min.thickness .030" (Haynes)

57-1363 / T1363
Plate, clutch, driven (steel)
Ref# 15 Fig. 10 Page 31 #7 (1969) (Req:6)
Clutch sprocket and housing unit

57-1370 / T1370
Bin K-4 (1/2/0)
Bush BoreDia 0.8135-.8145" Clearance .0032-47" Len 2 19/32"
Ref# 4 Fig. 8 Page 27 #7 (1969) (Req:1)
Mainshaft high gear
¹ Bush protrusion 7/16"
Before DU66247, none after)

57-1553 / T1553
Bin O-4 (2/0/0)
Screw, Phillips CEI/BSC/Cycle 1/4-26TPI X 3/8 U.H. Phillips
Ref# 43 Fig. 5 Page 21 #7 (1969) (Req:4)
Valve inspection cap lock spring

57-1570 / T1570
Sprocket (58T duplex) (Tool-Extractor D662/3)
Ref# 5 Fig. 10 Page 31 #7 (1969) (Req:1)
Clutch sprocket and housing
¹ Use DA50/1 before DU.48145

57-1604 / T1604
Bin K-2 (1/0/0)
Spring, camplate plunger (strong) 3-17/32" Long; 26 coils
Ref# 5 Fig. 7 Page 25 #7 (1969)
Gear selectors
¹ This (competition) spring is longer/stronger than 57-0373

57-1606 / T1606 TIMKEN M11121
Bin K5-S3 (1/3/0)
Bearing, layshaft high gear (D.S.) Closed end needle roller
11/16" x 7/8" x 3/4"
Ref# 14 Fig. 2 Page 15 #7 (1969) (Req:1)
Gearbox casing
¹ Also shown in Fig.7 as Ref.11
Ref# 11 Fig. 7 Page 25 #7 (1969) (Req:1)
Gearbox casing
¹ Also shown as Ref.14/Fig.2

57-1607 / T1607
Bin K-7 (1/2/0)
Washer, thrust New: .0905-.0910; Used 2018: .0938(outer)/.0916(inner spun)
Ref# 12 Fig. 7 Page 25 #7 (1969) (Req:2)
Gearbox inner cover, layshaft
Orient: Grooved side faces toward inside of gearbox

57-1614 / T1614 TIMKEN B1112
Bin K5-S3 (2/1/0)
Bearing, layshaft (T.S.) Open end needle roller
11/16" x 7/8" x 3/4"
Ref# 14 Fig. 7 Page 25 #7 (1969) (Req:1)
Layshaft

57-1646 / T1646
Cover, rubber
Ref# 28 Fig. 9 Page 29 #7 (1969) (Req:1)
Clutch cable abutment

57-1710 / T1710
Clutch lever shaft
Ref# 21 Fig. 9 Page 29 #7 (1969) (Req:1)
Clutch lever assembly

57-1711 / T1711
Thrust plate
Ref# 23 Fig. 9 Page 29 #7 (1969) (Req:1)
Clutch lever assembly

57-1712 / T1712
Bin L-6 (1/0/0)
Spring, conical
Ref# 24 Fig. 9 Page 29 #7 (1969) (Req:1)
Clutch lever assembly return spring (thrust plate)

57-1719 / T1719
Clutch center (Tool-Center Extractor)
Ref# 6 Fig. 10 Page 31 #7 (1969) (Req:1)
Clutch sprocket and housing

57-1720 / T1720
Plate, inner, clutch center
Ref# 7 Fig. 10 Page 31 #7 (1969) (Req:1)
Clutch center

57-1722 / T1722
Bin L-4 (3/0/0)
Rubber, drive (large)
Ref# 10 Fig. 10 Page 31 #7 (1969) (Req:3)
Clutch center

57-1723 / T1723
Bin L-4 (3/0/0)
Rubber, rebound (small)
Ref# 11 Fig. 10 Page 31 #7 (1969) (Req:3)
Clutch center

57-1724 / T1724
Plate, outer, clutch center
Ref# 12 Fig. 10 Page 31 #7 (1969) (Req:1)
Clutch center

57-1734 / T1734
Clutch hub (Tool-CD222)
Ref# 2 Fig. 10 Page 31 #7 (1969) (Req:1)
Clutch

57-1735 / T1735
Bin L-3 (1/2/0)
Washer, thrust Thickness .052/.054 in. Bronze or Copper & Steel
Ref# 3 Fig. 10 Page 31 #7 (1969) (Req:1)
Clutch center
Orient: 57-3931 bronze side to clutch basket / 57-1735 bevel to hub
¹ Use washer 57-1735 w hub 57-1734; Use 57-3931 w hub 57-3929

57-1736 / T1736
Bin - (1/0/0)
Clutch operating rod Len-11.822"/11.812" (11-13/16") Dia-.215" (7/32")
Ref# 27 Fig. 8 Page 27 #7 (1969) (Req:1)
Mainshaft

57-1738 / T1738
Bin D-3 (14/0/0)
Washer, fiber 7/16 x 11/16 x 3/32
Ref# 45 Fig. 2 Page 15 #7 (1969) (Req:1)
Primary chaincase drain/adjuster plug
¹ Also referenced as Ref 31 Figure 11
Ref# 31 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase drain/adjuster plug
¹ Also shown in Fig.2 as Ref.45

57-1770 / T1770
Bin - (5/0/0)
Joint washer
Ref# 24 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase cover

57-1771 / T1771
Bin L-6 (1/0/0)
Ball, steel 3/8" dia. (3/8 in. dia.)
Ref# 22 Fig. 9 Page 29 #7 (1969) (Req:3)
Clutch lever assembly, thrust plate
¹ Btwn clutch lever & thrust plate

57-1830 / T1830
Bin - (0/3/0)
Spring, clutch Free length 1 13/16 in.
Ref# 20 Fig. 10 Page 31 #7 (1969) (Req:3)
Clutch pressure plate

57-1896 / T1896
Bin K-2 (0/1/1)
Quadrant spindle
Ref# 18 Fig. 7 Page 25 #7 (1969) (Req:1)
Gear selectors

57-1916 / T1916
Sprocket
Ref# 12 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox (17T)

57-1917 / T1917
Sprocket
Ref# 12 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox (18T)

57-1918 / T1918
Sprocket (Tool-Z151)
Ref# 12 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox (19T)
¹ Countershaft sprocket/counter sprocket/front drive sprocket

57-1919 / T1919
Sprocket
Ref# 12 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox (20T)

57-1920 / T1920
Plug
Ref# 46 Fig. 2 Page 15 #7 (1969) (Req:1)
Gearbox blanking (rear)

57-1931 / T1931
Spring cup
Ref# 19 Fig. 10 Page 31 #7 (1969) (Req:3)
Clutch pressure plate

57-1952 / T1952
Sprocket
Ref# 12 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox (15T)

57-1953 / T1953
Sprocket
Ref# 12 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox (16T)

57-1955 / T1955
Bin - (1/0/0)
Oil seal housing, kickstarter
Ref# 7 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover

57-1956 / T1956
Bin D-3 (2/2/0)
Oil seal, kickstarter
Ref# 6 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover

57-1962 / T1962
Bin - (0/1/0)
Washer, plain 3/4"
Ref# 20 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox mainshaft

57-1963 / T1963
Bin - (0/1/0)
Sleeve
Ref# 21 Fig. 8 Page 27 #7 (1969) (Req:1)
Mainshaft, kickstarter pinion sleeve

57-2093 / T2093
LAYSHAFT, C/W HIGH GEAR (20T) Dia:.6845"T.S./6850"D.S.;Len: 6 31/64"
Ref# 11 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox
¹ Countershaft, output shaft

57-2116 / T2116
Bin K-9 (2/1/0)
Washer, tab (lock) Inside tabs
Ref# 13 Fig. 8 Page 27 #7 (1969) (Req:1)
Mainshaft, gearbox sprocket

57-2156 / T2156
Plate, clutch, pressure
Ref# 16 Fig. 10 Page 31 #7 (1969) (Req:1)
Clutch sprocket and housing unit

57-2159 / T2159
Pin, adjuster
Ref# 17 Fig. 10 Page 31 #7 (1969) (Req:1)
Clutch rod
¹ In till pressure plate lifts
Then back off 1 turn

57-2166 / T2166
Cap, inspection
Ref# 47 Fig.  2 Page 15 #7 (1969) (Req:1)
Primary chain case
Ref# 47 Fig.  2 Page 15 #7 (1969) (Req:1)
Primary chaincase filler/inspection port
Ref# 47 Fig.  9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover, filler/inspection port
Ref# 32 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase, clutch adjustment

57-2172 / T2172
Index plunger holder (Tool-3/4")
Ref# 6 Fig. 7 Page 25 #7 (1969) (Req:1)
Gear selectors

57-2173 / T2173
Kickstarter lever
Ref# 39 Fig. 9 Page 29 #7 (1969) (Req:1)
Kickstarter assembly

57-2191 / T2191
Clutch lever
Ref# 20 Fig. 9 Page 29 #7 (1969) (Req:1)
Clutch lever assembly

57-2240 / T2240
Bin K-3 (2/3/0)
Washer, tab
Ref# 25 Fig. 8 Page 27 #7 (1969) (Req:1)
Mainshaft T.S., kickstart ratchet

57-2279 / T2279
Bin L-5 (1/1/0)
Washer, cupped (flat) 9/16x1 3/8 Thickness: Original.160"; BCS.250"
Ref# 23 Fig. 10 Page 31 #7 (1969) (Req:1)
Clutch nut
¹ Cupped washer discontinued?

57-2316 / T2316
Mainshaft high gear (26T) Bore dia-.8135/.8145"; Clear-.0032/.0047"; Bush Len-2 19/32
Ref# 3 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox

57-2330 / T2330
Bin G-1 (2/0/0)
Rubber
Ref# 44 Fig. 9 Page 29 #7 (1969) (Req:1)
Kickstarter pedal

57-2331 / T2331
Rubber
Ref# 6 Fig. 12 Page 35 #7 (1969) (Req:1)
Center stand

57-2378 / T2378
Mainshaft third gear (24T)
Ref# 5 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox

57-2379 / T2379
Layshaft third gear (22T)
Ref# 10 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox

57-2436 / T2436
MAINSHAFT C/W LOW GEAR (16T) UNF (SAE) Dia.DS-.8098/.8103";TS-.7494/.7498";Len:11 19/64";9/16-18UNF
Ref# 1 Fig. 8 Page 27 #7 (1969) (Req:1)
Gearbox
¹ Input shaft, clutch shaft. (Prior to '67 - T914)

57-2440 / T2440
Cover, rotor
Ref# 26 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase

57-2442 / T2442
Bin D-7 (1/0/0)
Joint washer
Ref# 27 Fig. 11 Page 33 #7 (1969) (Req:1)
Rotor cover

57-2443 / T2443
Timing pointer
Ref# 38 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase cover

57-2450 / T2450
Bin G-2 (3/0/0)
Rubber
Ref# 37 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearchange pedal

57-2526 / T2526
Nut ASME 1/4-26TPI
Ref# 21 Fig. 10 Page 31 #7 (1969) (Req:3)
Clutch pressure plate spring adjustment

57-2538 / T2538
Shock absorber spider
Ref# 9 Fig. 10 Page 31 #7 (1969) (Req:1)
Clutch center
Orient: Wider shoulder engages inner clutch center plate

57-2559 / T2559
Drain and adjuster plug
Ref# 30 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase
¹ #7 Ref#44/p15 referenced as E6347

57-2595 / NT261
Bin K-2 (2/0/0)
Rollers O.D.:Orig (65Kmi).4370-72,SRM-.464-67,MAP-.4395
Ref# 9 Fig. 7 Page 25 #7 (1969) (Req:2)
Gear selector forks

57-2608 / T2608
Selector fork Longer barrel than 57-0913, lay shaft selector
Ref# 7 Fig. 7 Page 25 #7 (1969) (Req:1)
Mainshaft

57-3629 / T3629
ClUTCH LEVER ASSEMBLY
Ref# 19 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover

57-3632 / T3632
KICKSTARTER, FOLDING COMPLETE ASSEMBLY
Ref# 38 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover

57-3650 / T3650
Bin - (0/0/1)
Camplate
Ref# 3 Fig. 7 Page 25 #7 (1969) (Req:1)
Gearbox inner cover

57-3660 / T3660
Bin K-2 (0/1/1)
Plunger, camplate index
Ref# 4 Fig. 7 Page 25 #7 (1969) (Req:1)
Gearbox inner cover

57-3661 / T3661
Spring, camplate plunger Len:2-1/2"; Coils:22; Spring pressure:5-6 lbs/in.
Ref# 5 Fig. 7 Page 25 #7 (1969) (Req:1)
Gearbox inner cover

57-3757 / T3757
Gearchange pedal
Ref# 35 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover

57-3760 / T3760
Cover
Ref# 1 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover

57-3762 / T3762
Abutment (Tool-5/8"open)
Ref# 29 Fig. 9 Page 29 #7 (1969) (Req:1)
Clutch cable

57-3766 / T3766
Cover
Ref# 13 Fig. 7 Page 25 #7 (1969) (Req:1)
Gearbox inner cover

57-3851 / T3851
Drain plug (with level tube) BA (Tool-11/16-2"extension)
Ref# 40 Fig. 2 Page 15 #7 (1969) (Req:1)
Gearbox UN

57-3988 / PT108B
Bin L-6 (1/0/0)
Bush
Ref# 2 Fig. 8 Page 27 #7 (1969) (Req:1)
Clutch rod, T.S.

57-4117 / T25A
Kickstarter quadrant
Ref# 16 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover

6/132A
Bin M-1 (0/1/0)
Ferrule
Ref# 25 Fig. 31 Page 71 #7 (1969) (Req:2)
Choke cable, mixing chamber cover T120R

60-
60-0083 / D83
Nipple
Ref# 16 Fig. 28 Page 65 #7 (1969) (Req:1)
Throttle cable T120R
Ref# 24 Fig. 28 Page 65 #7 (1969) (Req:1)
Handlebar, choke cable T120R

60-0101 / D101
Ferrule
Ref# 15 Fig. 28 Page 65 #7 (1969) (Req:8)
Throttle cable T120R
Ref# 25 Fig. 28 Page 65 #7 (1969) (Req:6)
Choke cable T120R

60-0103 / D103
Ferrule
Ref# 10 Fig. 28 Page 65 #7 (1969) (Req:2)
Front brake cable
Ref# 2 Fig. 28 Page 65 #7 (1969) (Req:2)
Clutch cable

60-0104 / D104
Adjuster ASME 7/32 x 40
Ref# 18 Fig. 28 Page 65 #7 (1969) (Req:1)
Throttle cable T120R

60-0208-5 / D208-5
Screw, hammer drive
Ref# 3 Fig. 6 Page 23 #7 (1969) (Req:2)
Patent plate, timing cover

60-0262 / D262
Bin - (2/0/0)
Cover, rubber
Ref# 19 Fig. 35 Page 77 #7 (1969) (Req:2)
Spark plug

60-0374 / D374
Check wire
Ref# 15 Fig. 25 Page 59 #7 (1969) (Req:1)
Seat

60-0477 / D477
Chain, primary (3/8 in. duplex) (Tool-D496)
Ref# 15 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase
Orient: Shop manual: 3/8" (1/2" elsewhere) free tightest point

60-0494 / D494
Bin B-9 (0/1/0)
Circlip
Ref# 32 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach cable spade T120R-TR6R

60-0506 / D506
Nipple
Ref# 11 Fig. 28 Page 65 #7 (1969) (Req:1)
Front brake cable, handlebar end
Ref# 3 Fig. 28 Page 65 #7 (1969) (Req:1)
Clutch cable, handlebar end

60-0530 / D530 TSUBAKI 530QR
Chain, drive (5/8 x 3/8 in. x 104 links)*
Ref# 5 Fig. 11 Page 33 #7 (1969) (Req:1)
Rear wheel
Orient: Slack: 3/4" on tires, tightest; or 1 3/4" on stand, slackest
¹ '15@65K(TSU)'14@60K(TSU)'13@53K(REN)

60-0546 / D546
Plug
Fig. 33 Page 73 #7 (1969) (Req:1)
Tachometer bulb holder blanking plug

60-0578 / D578
Cable, tachometer Length 28 in.; metal sheath
Ref# 29 Fig. 33 Page 73 #7 (1969) (Req:1)
Tachometer T120R-TR6R
¹ Use copper washer spacer
To prevent "wobble" at drive end

60-0609 / D609
Cable, speedometer Length 65 inches. (Inner only: D609W) (Tool-9/16 rear wheel)
Ref# 15 Fig. 33 Page 73 #7 (1969) (Req:1)
Speedo
¹ #7 reverses tach cable (29)
And speedo (15) illustrations

60-0622 / D622
Bin A-3 (1/1/1)
Key, ignition w. tumbler
Ref# 33 Fig. 36 Page 79 #7 (1969) (Req:1)
Ignition key T120R-TR6R

60-0623 / D623
Key, frame lock
Ref# 11 Fig. 17 Page 45 #7 (1969) (Req:2)
Steering lock

60-0637 / D637 SMITHS BG5330/168
Bin S-1 (0/2/1)
Gearbox, speedometer 15:12 or 1.25:1 (same ratio) Grease nipple: 2BA
Ref# 39 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel spindle T.S.
¹ Britishfasteners- 2BA grease nipples w head for reg g.guns

60-0638 / D638
Fork end
Ref# 12 Fig. 28 Page 65 #7 (1969) (Req:1)
Front brake cable

60-0668 / D668
Adjuster
Ref# 5 Fig. 28 Page 65 #7 (1969) (Req:1)
Clutch cable adjuster (outer gearbox cover)

60-0684 / D684
Cable, choke
Ref# 22 Fig. 28 Page 65 #7 (1969) (Req:2)
Handlebars T120R

60-0696 / D696
Trim strip
Ref# 8 Fig. 25 Page 59 #7 (1969) (Req:1)
Seat

60-0697 / D697
Sprag
Ref# 9 Fig. 25 Page 59 #7 (1969) (Req:4)
Seat trim strip

60-0771 / D771 AMAL L930/10
Bin S1- (0/1/1)
Carburetter, L.H.
Ref# 1 Fig. 31 Page 71 #7 (1969) (Req:1)
Carburetter T120R
Orient: Gasline fitting on Banjo bolt: [rear][<][front]

60-0772 / D772 AMAL L930/9
Bin S1- (0/1/1)
Carburetter, R.H.
Ref# 1 Fig. 31 Page 71 #7 (1969) (Req:1)
Carburetter T120R
Orient: Gasline fitting on Banjo bolt: [rear][<][front]

60-1817 / D1817
Cable, choke
Ref# 20 Fig. 28 Page 65 #7 (1969) (Req:1)
Handlebars T120R

60-1818 / D1818
Lever, choke cable
Ref# 21 Fig. 28 Page 65 #7 (1969) (Req:1)
Handlebars T120R

60-1819 / D1819
Cable, throttle Original: 43"
Ref# 14 Fig. 28 Page 65 #7 (1969) (Req:1)
Handlebars T120R

60-1900 / D1900
Horn
Ref# 51 Fig. 35 Page 77 #7 (1969) (Req:1)
Right hand

60-1901 / D1901
Horn
Ref# 52 Fig. 35 Page 77 #7 (1969) (Req:1)
Left hand

60-1993 / D1993
Cable, clutch Original: 49";
Ref# 1 Fig. 28 Page 65 #7 (1969) (Req:1)
Handlebars

60-2024 / D2024 FROM I-NET 64052107
Shock absorber, rear 12-7/8" (12.9") Cen-Cen w. preload in center position
Ref# 16 Fig. 13 Page 37 #7 (1969) (Req:2)
Rear shock absorber

60-2026 / D2026
Bin D-9 (2/0/0)
Decal, Bonneville
Ref# 31 Fig. 22 Page 53 #7 (1969) (Req:1)
Oil tank

60-2045 / D2045
Bin G-3 (2/1/0)
Cover, rubber
Ref# 24 Fig. 6 Page 23 #7 (1969) (Req:1)
Oil pressure switch

60-2073 / D2073 AMAL 18/978
FRONT BRAKE AND CHOKE ASSEMBLY, COMPLETE
Ref# 13 Fig. 27 Page 63 #7 (1969) (Req:1)
Handlebars

60-2074 / D2074 AMAL 18/952
CLUTCH LEVER ASSEMBLY, COMPLETE
Ref# 26 Fig. 27 Page 63 #7 (1969) (Req:1)
Handlebars

60-2076 / D2076
Cable, brake Original: 32 1/2"
Ref# 7 Fig. 28 Page 65 #7 (1969) (Req:1)
Handlebars

60-2085 / D2085
Stop switch
Ref# 8 Fig. 28 Page 65 #7 (1969) (Req:1)
Front brake cable

60-2086 / D2086
Cover, rubber
Ref# 9 Fig. 28 Page 65 #7 (1969) (Req:1)
Front brake stoplight switch

60-2133 / D2133
Switch, oil pressure 27tpi 1/8"NPS(Straight) except early '69 - 1/8"NPT(Tapered) (Tool-5/16 BS)
Ref# 23 Fig. 6 Page 23 #7 (1969) (Req:1)
Timing cover
Torque: DON'T OVR!

60-2138 / D2138
Decal (Timing label)
Fig. 6 Page 23 #7 (1969)
Contact breaker cover

60-2364 / S70-3
Bin J-8 (40/40/0)
Ball, steel Dia. 1/4"
Ref# 3 Fig. 12 Page 35 #7 (1969) (Req:40)
Steering races
¹ Repack grease @12,000 miles

60-343/3 / D343/3
Rubber cable tie
Ref# 35 Fig. 36 Page 79 #7 (1969) (Req:1)
Ignition (rear lamp) T120R-TR6R

60-343/7 / D343/7
Clip, rubber
Ref# 27 Fig. 28 Page 65 #7 (1969)
Cable

60-3552 / S35-7
Bin - (0/1/0)
Bearing, mainshaft (T.S.) 3/4" x 1-7/8" x 9/16" Ball Journal (Tool-1-7/8" drift)
Ref# 18 Fig. 8 Page 27 #7 (1969) (Req:1)
Inner gearbox cover

60-4245 / S25-1
Bin C-1 (10/0/0)
Washer, plain 1/4 x 9/16 x 3/32
Ref# 21 Fig. 26 Page 61 #7 (1969) (Req:2)
Fender, Rear
¹ (12)total
Ref# 21 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, center stay
Ref# 21 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, front stay
Ref# 21 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, liscense plate bracket
Ref# 21 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, bridge
Ref# 21 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, lifting handle

60-4246 / S25-2
Bin C-1 (6/0/0)
Washer, plain 3/8 x (5/8)(3/4) x 1/16
Ref# 20 Fig. 2 Page 15 #7 (1969) (Req:2)
Crankcase Junction Stud
¹ Stud Ref.19
Ref# 22 Fig. 13 Page 37 #7 (1969) (Req:2)
Rear shock absorber mount, head of lower bolt 37/21
Ref# 5 Fig. 17 Page 45 #7 (1969) (Req:2)
Stanchion tube pinch bolt 45/4

60-4247 / S25-3
Bin C-1 (7/1/0)
Washer, plain 5/16 x 5/8 x 1/16 (.040)
Ref# 35 Fig.  2 Page 15 #7 (1969) (Req:11)
Crankcase D.S.
¹ Bolts 15/30-31-32 and ??
Ref# 28 Fig.  5 Page 21 #7 (1969) (Req:1)
Cylinder head bolt (center bolt)
Ref# 30 Fig.  9 Page 29 #7 (1969) (Req:2)
Domed nuts, gearbox outer cover
Ref# 22 Fig. 11 Page 33 #7 (1969) (Req:3)
Stator mounting stud
Ref# 33 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard, stepped bolt 37/32
Ref# 10 Fig. 14 Page 39 #7 (1969) (Req:3)
Engine mount bolt 39/8, D.S. top, front
Ref# 10 Fig. 14 Page 39 #7 (1969) (Req:1)
Engine mount plate
Ref# 27 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, bottom stay (to lower fork leg)
Ref# 27 Fig. 26 Page 61 #7 (1969) (Req:1)
Front fender, bottom stay (to fender)

60-4248 / S25-13
Bin C-1 (6/3/0)
Washer, plain 1/4 x 15/32 x .064
Ref# 37 Fig. 5 Page 21 #7 (1969) (Req:4)
Rocker box mount bolts
Ref# 30 Fig. 13 Page 37 #7 (1969) (Req:1)
Rear brake operating rod
Ref# 29 Fig. 23 Page 55 #7 (1969) (Req:4)
Battery holder straps, front/rear

60-4250 / S26-2
Bin C-2 (11/2/0)
Washer, spring 1/4
Ref# 3 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chain oiler tube clip
Ref# 38 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard C-clamp
Ref# 13 Fig. 25 Page 59 #7 (1969) (Req:4)
Seat, hinge
Ref# 23 Fig. 25 Page 59 #7 (1969) (Req:4)
Seat, rail
Ref# 45 Fig. 35 Page 77 #7 (1969) (Req:1)
Zener diode bracket
¹ Fastens heatsink to bracket
Ref# 55 Fig. 35 Page 77 #7 (1969) (Req:6)
Horn relay bracket

60-4251 / PCW73A
Bin C-4 (3/0/0)
Washer, spring
Ref# 22 Fig. 12 Page 35 #7 (1969) (Req:2)
Front/rear frame, bottom rear under bolt 35/23
Ref# 13 Fig. 13 Page 37 #7 (1969) (Req:2)
Swinging fork, torque stay
Ref# 2 Fig. 14 Page 39 #7 (1969) (Req:4)
Engine mounting stud
¹ Stud, Ref.1

60-4253 / S66-1
Bin L-5 (1/0/0)
Key Half-moon
Ref# 22 Fig. 10 Page 31 #7 (1969) (Req:1)
Mainshaft/Clutch hub

60-4256 / GS299 LUCAS 188330
Bin C-4 (6/7/7)
Washer, serrated 3/16
Ref# 16 Fig. 6 Page 23 #7 (1969) (Req:2)
Contact breaker cover plate
Ref# 36 Fig. 26 Page 61 #7 (1969) (Req:1)
Stoplight
Ref# 34 Fig. 35 Page 77 #7 (1969) (Req:2)
Condenser bracket
Ref# 39 Fig. 35 Page 77 #7 (1969) (Req:3)
Horn mount
Ref# 5 Fig. 35 Page 77 #7 (1969) (Req:4)
Ignition coil

60-4259 / S26-1
Bin C-2 (8/2/2)
Washer, spring 3/8 x 19/32 x 7/32
Ref# 17 Fig. 12 Page 35 #7 (1969) (Req:2)
Main/rear frame (top)
Ref# 23 Fig. 13 Page 37 #7 (1969) (Req:2)
Rear shock absorber mount, lower nut 37/25
Ref# 25 Fig. 14 Page 39 #7 (1969) (Req:1)
Brake pedal
Ref# 25 Fig. 14 Page 39 #7 (1969) (Req:4)
Engine mount plate, top/front, T.S.
Ref# 25 Fig. 14 Page 39 #7 (1969) (Req:4)
Torque stay, head bolts 21/38 (bolts 2,3,4,5)
¹ S26-1 is too small- Use S26-3

60-4260 / S26-3
Bin C-2 (10/0/0)
Washer, spring 5/16
Ref# 11 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine torque stay, bolt 39/30
Ref# 11 Fig. 14 Page 39 #7 (1969) (Req:4)
Engine torque stays
Ref# 12 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust pipe bracket/exhaust pipe, screw 41/13
Ref# 17 Fig. 15 Page 41 #7 (1969) (Req:4)
Muffler hanger bracket, bolt 41/18
Ref# 22 Fig. 15 Page 41 #7 (1969) (Req:4)
Muffler hanger (to frame), bolt 41/20, nut 41/21
Ref# 24 Fig. 15 Page 41 #7 (1969) (Req:2)
Muffler hanger (to muffler bracket), bolt 41/23, nut 41/25
Ref# 30 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust pipe to muffler clamp, bolt 41/29
Ref# 37 Fig. 17 Page 45 #7 (1969) (Req:4)
Lower fork leg spindle cap
Ref# 34 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, frame bracket
Ref# 49 Fig. 35 Page 77 #7 (1969) (Req:1)
Zener diode bracket
¹ Fastens bracket to middle lug

60-4263 / WE170
Bin O-4 (8/0/0)
Washer, fiber
Ref# 42 Fig. 5 Page 21 #7 (1969) (Req:4)
Rocker box inspection cap locking spring
¹ Use 60-4263
Ref# 4 Fig. 13 Page 37 #7 (1969) (Req:1)
Swinging fork grease nipple

643
Bin A-5 (4/0/0)
Bulb 3W. MES (Miniature Edison Screw base)
Ref# 2 Fig. 33 Page 73 #7 (1969) (Req:2)
Speedo/Tach
¹ #7 Error Qty should be 2, not 1

70-
70-0327 / E327
Bin O-2 (0/4/4)
Bolt (head bolt) ASME 3/8-26TPI X 3-3/8 U.H. (Tool-3/8BS-5/16W)
Ref# 25 Fig. 5 Page 21 #7 (1969) (Req:4)
Cylinder head (outer bolt)
Torque: 18 LBS

70-0375 / E375
Spindle
Ref# 15 Fig. 2 Page 15 #7 (1969) (Req:1)
Timing chest T.S., intermediate wheel

70-0400 / E400
Bush, intermediate wheel
Ref# 30 Fig. 1 Page 13 #7 (1969) (Req:1)
Timing chest

70-0403 / E403
Oil pump valve spring
Ref# 7 Fig. 3 Page 17 #7 (1969) (Req:2)
Oil pump

70-0470 / E0470
Bin O-5 (0/4/0)
Nut CEI/BSC/Cycle 5/16-26TPI .038 Pitch (Tool-3/16W or adj tool)
Ref# 48 Fig. 5 Page 21 #7 (1969) (Req:4)
Valve adjuster lock
¹ Adj at 3Kmi (ha-ha)
1/4 turn=.01"
Ex.004" In.002"

70-0489 / E489
Bin K-6 (1/1/0)
Circlip
Ref# 16 Fig. 8 Page 27 #7 (1969) (Req:1)
High gear bearing

70-0495 / E495
Oil pump drive block
Ref# 5 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil pump
¹ Haynes says replace when removed

70-1310 / E1310
Bin N-2 (1/0/0)
Nut CEI/BSC/Cycle 5/16-26TPI Thin Wall (Tool-1/4 BS)
Ref# 15 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil pipes and junction block

70-1330 / E1330
Bin O-5 (0/2/2)
Washer, thrust 3/8"
Ref# 49 Fig. 5 Page 21 #7 (1969) (Req:2)
Rocker spindles, Exhaust/Inlet T.S.

70-1335 / E1335
Bin O-6 (6/5/0)
Washer, copper 3/8 x 5/8 x 1/32
Ref# 33 Fig. 23 Page 55 #7 (1969) (Req:4)
Rocker oil feed pipe

70-1435 / E1435
Bin O-6 (2/2/2)
Nut, domed ASME 3/8-26TPI (Tool-3/8BS 5/16W)
Ref# 34 Fig. 23 Page 55 #7 (1969) (Req:2)
Rocker oil feed pipe
Torque: 22 LBS
¹ Changed to 24TPI (UNF) in 1973; beware of mismatches

70-1457 / E1457
Rocker Rocker bore (new): .5002 to .5012 (Newsgroup)
Ref# 44 Fig. 5 Page 21 #7 (1969) (Req:2)
Rocker box T.S. exhaust and D.S. inlet

70-1458 / E1458
Rocker Rocker bore (new): .5002 to .5012 (Newsgroup)
Ref# 45 Fig. 5 Page 21 #7 (1969) (Req:2)
Rocker box D.S. exhaust and T.S. inlet

70-1463 / E1463
Bin N-2 (0/0/0)
Nut (inlet camshaft pinion) LEFT-HAND (Tool-1")
Ref# 33 Fig. 1 Page 13 #7 (1969) (Req:1)
Camshaft, inlet

70-1479 / E1479
Bin - (2/0/0)
Bushing, T.S. Camshafts
Ref# 9 Fig. 2 Page 15 #7 (1969) (Req:2)
Camshaft, Intake and Exhaust

70-1511 / E1511
Bush, phosphor bronze OD.8140-.8145" BoreD.6890-.6894" Len 1.030-1.031"
Ref# 9 Fig. 1 Page 13 #7 (1969) (Req:2)
Con rod, small end

70-1512 / E1512
Bin O-6 (0/3/2)
Spindle, rocker New:.4990-.4995(WS Man);Bores:.5002-.5012 (Newsgroup)
Ref# 52 Fig. 5 Page 21 #7 (1969) (Req:2)
Rocker box

70-1513 / E1513
Bin O-5 (0/4/4)
Pin, adjusting CEI/BSC/Cycle 5/16-26TPI .038 Pitch
Ref# 47 Fig. 5 Page 21 #7 (1969) (Req:4)
Valve adjustment
¹ Adj at 3Kmi (ha-ha)
1/4 turn=.01" Ex.004" In.002"

70-1516 / E1516
Bin - (1/0/0)
Bushing, Camshaft, Left Hand/D.S.
Ref# 5 Fig. 2 Page 15 #7 (1969) (Req:1)
Camshaft, exhaust D.S.

70-1532 / E1532
Bin - (2/0/0)
Hollow dowel - tappet oil feed
Ref# 22 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase T.S. forward
¹ Wrong part number (70-8751) and Qty (2) in #7

70-1543 / E1543
Top collar
Ref# 23 Fig. 5 Page 21 #7 (1969) (Req:4)
Cylinder head, valve stem

70-1558 / E1558
Bin - (1/0/0)
Key, pinion
Ref# 32 Fig. 1 Page 13 #7 (1969) (Req:2)
Camshafts

70-1574 / E1574
Bin O-5 (0/4/4)
Washer, spring 9/16" Thackeray
Ref# 51 Fig. 5 Page 21 #7 (1969) (Req:4)
Rocker spindle

70-1575 / E1575
Bin O-5 (0/8/8)
Washer, thrust 1/2"
Ref# 50 Fig. 5 Page 21 #7 (1969) (Req:6)
Rocker spindles, 3 Inlet/3 Exhaust

70-1580 / E1580
Bin N-2 (1/0/0)
Key
Ref# 26 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft, T.S.
¹ Crankshaft pinion wheel

70-1591 / E1591
Bearing, crankshaft main (T.S.) 2-13/16"x 1-1/8"x 13/16" Ball journal (Tool-Z14 (see B40))
Ref# 18 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft T.S.

70-1596 / E1596
Bin 0-2 (0/4/4)
Bolt (head bolt) CEI/BSC/Cycle 3/8-26TPI X 5-7/8 U.H. (Tool-3/8BS-5/16W)
Ref# 38 Fig. 5 Page 21 #7 (1969) (Req:4)
Cylinder head (torque stays)
Torque: 18 LBS

70-1612 / E1612
Bin C-5 (3/1/0)
Washer, serrated 1/4x7/16 serrated internal
Ref# 14 Fig. 9 Page 29 #7 (1969) (Req:4)
Gearchange guideplate
Ref# 10 Fig. 20 Page 51 #7 (1969) (Req:8)
Rear wheel chain sprocket
¹ Also gearchange guideplate 29/14
Ref# 23 Fig. 35 Page 77 #7 (1969) (Req:6)
Ignition coil bracket T120R-TR6C

70-1670 / E1670
Bin D-3 (3/0/0)
Washer, fiber 7/8"x1-1/16"x.39"
Ref# 19 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil release valve

70-1719A / E1719A
Washer
Ref# 17 Fig. 25 Page 59 #7 (1969) (Req:1)
Seat latch

70-2256 / E2256
Bin N-3 (0/1/0)
Spring, rotary breather valve
Ref# 39 Fig. 1 Page 13 #7 (1969) (Req:1)
Camshaft, inlet

70-2260 / E2260
Bin - (1/0/0)
Bushing, Camshaft
Ref# 4 Fig. 2 Page 15 #7 (1969) (Req:1)
Camshaft, Intake D.S.

70-2271 / E2271
Bin H-5 (0/2/0)
Clamp 1 5/8"
Ref# 26 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust pipe to muffler

70-2287 / E2287
Washer, spring
Ref# 33 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, clip

70-2311 / E2311
Pin
Ref# 3 Fig. 2 Page 15 #7 (1969) (Req:1)
Breather disk locating pin, crankcase D.S.

70-2351 / E2351 LUCAS 131023
Bin B-4 (3/0/0)
Washer, plain
Ref# 4 Fig. 35 Page 77 #7 (1969) (Req:4)
Ignition coil

70-2360 / E2360
Oil pump screwed plug
Ref# 8 Fig. 3 Page 17 #7 (1969) (Req:2)
Oil pump

70-2440 / E2440
Washer, copper
Ref# 32 Fig. 3 Page 17 #7 (1969) (Req:2)
Tappet guide set bolt

70-2441 / E2441
Bin D-4 (2/1/0)
Washer, copper Copper 1/4" I.D. x 7/16" x 1/32"
Ref# 43 Fig. 2 Page 15 #7 (1969) (Req:1)
Gearbox drain/level plug 15/42
¹ Same as 33/29 for chaincase level plug
Ref# 29 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase level plug
¹ Same as gearbox level/drain

70-2620 / E2620
Bin O-1 (2/4/0)
Pushrod 6-5/16"
Ref# 4 Fig. 5 Page 21 #7 (1969) (Req:4)
Pushrod

70-2724 / E2724
Pipe, metal
Ref# 7 Fig. 2 Page 15 #7 (1969) (Req:1)
Breather pipe, crankcase (beneath)

70-2879 / E2879
Bearing, crankshaft main (D.S.) 2-13/16 x 1-1/8 x 13/16"
UC-single-lip roller (Tool-Z162 (see B40))
Ref# 41 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft, D.S.

70-2888 / E2888
Stud, crankcase junction CEI/BSC/Cycle 5/16-26TPI X 3-7/8 O.A.
Ref# 34 Fig. 2 Page 15 #7 (1969) (Req:2)
Crankcase
Torque: 20 LBS
¹ Crankcase junct studs #4,5

70-2904 / E2904
Valve, exhaust
Ref# 19 Fig. 5 Page 21 #7 (1969) (Req:2)
Cylinder head

70-2968 / E2968
Insulating block Phonelic
Ref# 31 Fig. 31 Page 71 #7 (1969) (Req:1)
Carburetter
¹ '68 and earlier, use w NA43A gasket & 244/1048 o-ring

70-2980 / E2980
Bin F-9 (1/0/0)
Stud, rocker boxes BSW/BSF 1/4-20TPI/26TPI X 15/16 O.A.
Ref# 33 Fig. 5 Page 21 #7 (1969) (Req:6)
Rocker box
Ref# 38 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender

70-3059R / E3059R
Bin O-1 (0/2/2)
Tappet, inlet "R" Radius
Ref# 34 Fig. 3 Page 17 #7 (1969) (Req:2)
Tappet guide block

70-3114 / E3114
Stud, rotor ASME 7/16-26TPI X 1 3/8 O.A.
Ref# 7 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft, D.S.

70-3253 / E3253
Bin D-1 (6/0/0)
O-ring Viton/Dash#11/Nom.CS 1/16"/ID 5/16"
Ref# 29 Fig. 5 Page 21 #7 (1969) (Req:2)
Rocker spindle
¹ Use updated Triumph p/n 60-3548

70-3300 / E3300
Bin N-4 (0/1/0)
Washer, clamping (thrust)
Ref# 40 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft, T.S.
Orient: Chamfer faces main bearing (H Hancox)

70-3302 / E3302
Bin C-6 (5/5/0)
Washer, plain 1/4 x 1/2 x.031
Ref# 35 Fig. 5 Page 21 #7 (1969) (Req:6)
Rocker box mount stud

70-3309 / E3309
Bin D-1 (13/0/0)
O-ring Viton/Dash#15/Nom.CS 1/16"/ID 9/16"
Ref# 9 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearchange quadrant
Ref# 27 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach driven gear housing T120R-TR6R
¹ Also used on gearchange quadrant, Fig 9 Reference 9

70-3446 / E3446
Bin C-7 (2/0/0)
Washer, plain O.D. 17/32 in. I.D. 5/32 in. Thick ~1/16 in.
Ref# 21 Fig. 7 Page 25 #7 (1969) (Req:1)
Gearbox inner cover
Ref# 14 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil pipe junction block

70-3586 / E3586
Bearing, shells
Ref# 12 Fig. 1 Page 13 #7 (1969) (Req:4)
Con rod

70-3716 / E3716
Bin N-4 (0/0/0)
Hollow dowel - crankcase bolt .373"X.566" (Baxter)
Ref# 17 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase - DS cylinder base
¹ Location shown in #7 Fig.2 is incorrect

70-3730 / E3730
Bin D-5 (3/0/0)
Joint washer
Ref# 9 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil pump
¹ No gasket sealer necessary

70-3751 / E3751
Bin D-3 (3/0/0)
Joint washer, fiber Fiber
Ref# 40 Fig. 5 Page 21 #7 (1969) (Req:4)
Rocker box, valve inspection cap

70-3763 / E3763
Bin D-5 (3/0/0)
Joint gasket
Ref# 13 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil pipes, junction block
¹ No gasket sealer necessary

70-3768 / E3768
Washer, D
Ref# 28 Fig. 15 Page 41 #7 (1969) (Req:4)
Muffler clamp 41/26
Ref# 34 Fig. 15 Page 41 #7 (1969) (Req:4)
Exhaust crossover pipe

70-3821 / E3821
Bin L-5 (1/9/0)
Screw, countersunk BA 2BA X 5/16 X 15/16" U.H. (Tool-Impact big handle)
Ref# 9 Fig. 11 Page 33 #7 (1969) (Req:6)
Inner cover plate

70-3827 / E3827
Valve guide, inlet
Ref# 10 Fig. 5 Page 21 #7 (1969) (Req:2)
Cylinder head

70-3828 / E3828
Valve guide, exhaust
Ref# 11 Fig. 5 Page 21 #7 (1969) (Req:2)
Cylinder head

70-3832 / E3832
Bin - (2/0/0)
Joint washer
Ref# 6 Fig. 11 Page 33 #7 (1969) (Req:1)
Inner cover plate

70-3876 / E3876
Bin N-1 (5/0/0)
Oil seal 2-1/8"x 1-27/64"
Ref# 19 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft, D.S.
Orient: Springs to Primary(Fig.B39 WSMan)/or Crankcase("Experts")

70-3887 / E3887
Bin - (4/0/0)
Washer, serrated Serrated/conical
Ref# 11 Fig. 3 Page 17 #7 (1969) (Req:2)
Oil pump

70-3903 / E3903
Bin - (1/0/0)
Crankshaft oil tube (sludge trap)
Ref# 3 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft

70-3905 / E3905
Bin N-4 (1/0/0)
Screw plug
Ref# 4 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft sludge tube

70-3907 / E3907
Bolt
Ref# 6 Fig. 1 Page 13 #7 (1969) (Req:3)
Crankshaft, flywheel
Torque: 33 LBS

70-3975 / E3975
Bin L-2 (3/1/0)
Washer, tab 3/4
Ref# 24 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft, D.S.
¹ Beneath shouldered rotor nut

70-3977 / E3977
Nut, shouldered ASME 7/16-26TPI - Locktite 243 (blue)
Ref# 25 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft, D.S.
Torque: 30 LBS
¹ Lock clutch basket, not brake for accurate torque reading

70-4016 / E4016
Patent plate
Ref# 2 Fig. 6 Page 23 #7 (1969) (Req:1)
Timing cover

70-4144 / E4144
Bin G-4 (3/1/0)
Grommet, rubber
Ref# 20 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase, alternator leads
Orient: Inside primary chaincase

70-4152 / E4152
Tie rod
Ref# 12 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chain tensioner

70-4221 / E4221
Valve spring, inner (red spot) (Tool-Spring compressor)
Ref# 21 Fig. 5 Page 21 #7 (1969) (Req:4)
Cylinder head, valve stem

70-4538 / E4538
Scavenge pipe 5/16" reinforced rubber
Ref# 10 Fig. 2 Page 15 #7 (1969)
Crankcase oil filter
¹ Reference only

70-4547 / E4547
Bin S2- (1/4/0)
Gasket, cylinder head Copper Standard: .048" (JH)
Ref# 7 Fig. 5 Page 21 #7 (1969) (Req:1)
Cylinder head

70-4550 / E4550
Rocker box
Ref# 30 Fig. 5 Page 21 #7 (1969) (Req:1)
Inlet

70-4551 / E4551
Rocker box
Ref# 31 Fig. 5 Page 21 #7 (1969) (Req:1)
Exhaust

70-4562 / E4562
Wheel, inlet/exhaust camshaft pinion
Ref# 31 Fig. 1 Page 13 #7 (1969) (Req:2)
Camshafts
¹ Camshaft pinion gears

70-4563 / E4563
Bin N-5 (0/1/0)
Nut (exhaust camshaft pinion) LEFT-HAND (Tool-5/8W, 11/16BSF)
Ref# 34 Fig. 1 Page 13 #7 (1969) (Req:1)
Camshaft, exhaust

70-4564 / E4564
Wheel, crankshaft pinion
Ref# 27 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft, T.S.
¹ Crankshaft pinion gear

70-4565 / E4565
Bin N-5 (0/0/0)
Nut (crankshaft pinion) 3/4-20TPI (Tool-5/8W, 11/16BS)
Ref# 28 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft, T.S.
Torque: 30/80LBS
¹ Late '71 models w UN crankshaft threads use nut 71-2877

70-4568 / E4568
Bin N-1 (2/0/0)
Oil seal Use Pioneer & Weston, marked "PW"
Ref# 4 Fig. 6 Page 23 #7 (1969) (Req:2)
Crankshaft T.S.(1) Exhaust Camshaft (1)
Orient: Crankshaft-spring OUT; Exhaust Cam-spring IN (to engine)

70-4569 / E4569
Bin N-5 (2/0/0)
Circlip
Ref# 5 Fig. 6 Page 23 #7 (1969) (Req:1)
Crankshaft oil seal T.S.

70-4573 / E4573
Distance piece, sprocket to rotor
Ref# 21 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft, D.S.
Orient: Chamfer towards sprocket

70-4594 / E4594
Tubing, oil hose 5/16"
Ref# 10 Fig. 23 Page 55 #7 (1969) (Req:2)
Oil tank to oil pipe and junction block

70-4603 / E4603
Valve, inlet
Ref# 18 Fig. 5 Page 21 #7 (1969) (Req:2)
Cylinder head

70-4609 / E4609
Bin O-4 (2/0/0)
Spring, locking
Ref# 41 Fig. 5 Page 21 #7 (1969) (Req:4)
Valve adjustment inspection cap

70-4610 / E4610
Bin O-4 (2/2/2)
Cap, inspection
Ref# 39 Fig. 5 Page 21 #7 (1969) (Req:4)
Valve adjustment

70-4643 / E4643
CRANKSHAFT C/W OIL TUBE
Ref# 2 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft

70-4700 / E4700
Drive thimble, tachometer
Ref# 37 Fig. 1 Page 13 #7 (1969) (Req:1)
Exhaust camshaft

70-4704 / E4704
Tube, oiler
Ref# 1 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chain oiler tube

70-4705 / E4705
Clip
Ref# 2 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chain oiler tube

70-4707 / E4707
Bin G-4 (2/0/0)
Grommet, rubber
Ref# 11 Fig. 6 Page 23 #7 (1969) (Req:1)
Contact breaker leads

70-4711 / E4711
Hanger
Ref# 19 Fig. 15 Page 41 #7 (1969) (Req:2)
Muffler and rear footpeg

70-4752 / E4752
Bin D-1 (6/0/0)
Sealing ring ID 15/16; OD 1 3/16; 1/8" (3.2mm) thick; square profile
Ref# 63 Fig. 5 Page 25 1971 PARTS (Req:2)
Pushrod cover tube, bottom

70-4771 / E4771
Bin O-3 (1/0/0)
Bolt (head bolt) CEI/BSC/Cycle 5/16-26TPI X 3 U.H. (Tool-5/16BS - 1/4W)
Ref# 27 Fig. 5 Page 21 #7 (1969) (Req:1)
Cylinder head (center bolt, 9-bolt head)
Torque: 15 LBS

70-4778 / E4778
Torque stays
Ref# 29 Fig. 14 Page 39 #7 (1969) (Req:4)
Cylinder head to frame, head bolts 2,3,4,5 and bolts 39/30

70-4792 / E4792
Pipe, balance
Ref# 15 Fig. 5 Page 21 #7 (1969) (Req:1)
Inlet manifold

70-4849 / E4849
Dowel pin
Ref# NI Fig. 6 Page 23 #7 (1969)
Auto advance unit

70-4856 / E4856
Stud, crankcase junction CEI/BSC/Cycle 5/16-26TPI X 5-1/16 O.A.
Ref# 33 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase
Torque: 20 LBS
¹ Crankcase junction stud #3

70-4951 / E4951
Bracket
Ref# 16 Fig. 15 Page 41 #7 (1969) (Req:2)
Muffler

70-5049 / E5049
Bin B-5 (2/0/0)
Joint washer
Ref# 15 Fig. 6 Page 23 #7 (1969) (Req:1)
Contact breaker cover plate

70-5155 / E5155
Bush, flanged
Ref# 19 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach gear housing T120R-TR6R

70-5157 / E5157
Driving gear
Ref# 20 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach gear housing T120R-TR6R

70-5315 / E5315
Bin D-4 (1/0/0)
Washer, copper
Ref# 38 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase filter
¹ Alt: O-Ring 70-7310 (TSB);
hydraulic seal washer

70-5316 / E5316
Valve, rotary breather
Ref# 38 Fig. 1 Page 13 #7 (1969) (Req:1)
Camshaft, inlet

70-5347 / E5347
Sleeve
Ref# 9 Fig. 5 Page 21 #7 (1969) (Req:2)
Head bolts through inlet tracts

70-5370 / E5370
Connector, Tee
Ref# 17 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank breather vent

70-5375 / E5375
Breather extension pipe I.D.3/8" Length: 30" Thin-wall
Ref# 39 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase (bottom)

70-5446 / E5446
Sprocket, engine 29T Duplex (Tool-Z151 WassellTL107)
Ref# 20 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft, D.S.
Orient: Flange for oil seal faces out

70-5449 / E5449
Plastic sleeve
Ref# 21 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chain tensioner

70-5578 / E5578
Driven gear
Ref# 23 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach driven gear housing T120R-TR6R

70-5676 / E5676
Brace
Ref# 27 Fig. 15 Page 41 #7 (1969) (Req:1)
Muffler/muffler

70-5759 / E5759
End cap
Ref# 21 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach gear housing T120R-TR6R

70-5866 / E5866
Muffler
Ref# 15 Fig. 15 Page 41 #7 (1969) (Req:2)
Muffler

70-5881 / E5881
Screw Set screw
Ref# 28 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach gear housing T120R-TR6R

70-5963 / E5963
Stud, crankcase junction CEI/BSC/Cycle 5/16-26TPI X 4-3/4 O.A.
Ref# 50 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase
Torque: 20 LBS
¹ Crankcase junction stud #2

70-5976 / E5976
Chain tensioner abutment
Ref# 6 Fig. 2 Page 15 #7 (1969) (Req:1)
Primary chaincase
Ref# 10 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase

70-5977 / E5977
Trunnion
Ref# 13 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chain tensioner

70-6061 / E6061
Bin - (0/1/0)
Tensioner blade
Ref# 11 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chain tensioner
¹ BCS: 70-6283(Tri 500) OK

70-6122 / E6122
Bin - (1/0/0)
Driven gear housing
Ref# 24 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach driven gear housing T120R-TR6R
¹ INC Brass Bush Ref.26

70-6159 / E6159
Wheel, intermediate pinion
Ref# 29 Fig. 1 Page 13 #7 (1969) (Req:1)
Timing chest
¹ Intermediate pinion gear

70-6179 / E6179
Screw, Phillips Phillips (Tool-7/16 for nut)
Ref# 13 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust pipe bracket/exhaust pipe

70-6299 / E6299
Bin B-9 (2/0/0)
O-ring Viton/Dash#11/Nom.CS 1/16"/ID 5/16"
Ref# 25 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach driven gear housing T120R-TR6R

70-6300 / E6300
Bin B-9 (3/0/0)
O-ring Viton/Dash#17/Nom. CS 1/16"/ID 11/16"
Ref# 22 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach gear housing plug T120R-TR6R

70-6304 / E6304
Cylinder block
Ref# 2 Fig. 5 Page 21 #7 (1969) (Req:1)
Cylinder block

70-6309 / E6309
Bin - (4/0/0)
Joint washer 650 1963-82
Ref# 1 Fig. 5 Page 21 #7 (1969) (Req:1)
Cylinder base
¹ No gasket sealer necessary

70-6347 / E6347
Drain and adjuster plug BSF 7/16"
Ref# 44 Fig. 2 Page 15 #7 (1969) (Req:1)
Primary chaincase
¹ #7 p.33/ref.30 references this part as T2559

70-6349 / E6349
Bin - (0/1/1)
Rocker oil feed pipe
Ref# 32 Fig. 23 Page 55 #7 (1969) (Req:1)
Rocker box

70-6353 / E6353
Rubber connector
Ref# 31 Fig. 23 Page 55 #7 (1969) (Req:1)
Rocker oil feed pipe

70-6356 / E6356
Tubing, froth tower vent
Ref# 16 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank
¹ Short tube from Tee (70-5370) to oil tank froth tower

70-6386 / E6386
Locating peg
Ref# 11 Fig. 2 Page 15 #7 (1969)
Oil pipes and junction block
¹ Reference only

70-6387 / E6387
Bin N-1 (1/0/0)
Oil seal 0.020" Undersize for re-ground crank
Ref# 4 Fig. 6 Page 23 #7 (1969) (Req:1)
Crankshaft T.S.

70-6388 / E6388
Ignition coil 12v/points 6v/Pazon
Ref# 26 Fig. 35 Page 77 #7 (1969) (Req:2)
Ignition coil T120R-TR6C

70-6389 / E6389
Clip, Siba 32,000/1
Ref# 27 Fig. 35 Page 77 #7 (1969) (Req:2)
Ignition coil T120R-TR6C

70-6439 / E6439
Bottom cup
Ref# 20 Fig. 5 Page 21 #7 (1969) (Req:4)
Cylinder head, valve stem

70-6559 / E6559
Washer, plain
Ref# 13 Fig. 6 Page 23 #7 (1969) (Req:2)
Contact breaker assembly pillar bolt

70-6576 / E6576
Bin S-M (0/4/0)
Bolt UNF (SAE) 5/16-24TPI
Ref# 10 Fig. 1 Page 13 #7 (1969) (Req:4)
Con rod
Torque: 28 LBS

70-6595 / E6595
OIL RELEASE VALVE ASSEMBLY
Ref# 13 Fig. 3 Page 17 #7 (1969) (Req:1)
Timing cover

70-6596 / E6596
Nut, domed (release valve cap) (Tool-15/16)
Ref# 16 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil release valve, crankcase T.S.

70-6681 / E6681
Oil pump scavenge plunger
Ref# 4 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil pump

70-6744 / E6744
Bin H-3 (3/0/0)
Bolt UNF (SAE) 5/16-24TPI
Ref# 10 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust pipe/head clamp

70-6848 / E6848
Bin H-8 (5/5/0)
Clip 9/16"
Ref# 11 Fig. 23 Page 55 #7 (1969) (Req:4)
Oil hoses

70-6849 / E6849
Clip
Ref# 39 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank flexible pipe, rocker oil feed pipe

70-6857 / E6857
Bin H-4 (0/2/2)
Bracket
Ref# 11 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust pipe
Orient: Mounts behind exhaust pipe tab

70-6861 / E6861
Pin, gudgeon Gudgeon pin hole dia. 0.6882"-.6886"
Ref# 16 Fig. 1 Page 13 #7 (1969) (Req:2)
Con rod

70-6864 / E6864
Ring, taper compression Fitted gap: .010/.014 in. (Tool-Z22 75mm)
Ref# 14 Fig. 1 Page 13 #7 (1969) (Req:4)
Piston

70-6865 / E6865
Ring, oil control Fitted gap: .010/.014 in. (Tool-Z22 75mm)
Ref# 15 Fig. 1 Page 13 #7 (1969) (Req:2)
Piston

70-6869 / E6869
Circlip, gudgeon pin
Ref# 17 Fig. 1 Page 13 #7 (1969) (Req:4)
Con rod

70-6916 / E6916
Connector
Ref# 14 Fig. 5 Page 21 #7 (1969) (Req:2)
Carburetter balance pipe

70-6930 / E6930
Pipes, oil, and junction block 5/16" pipe
Ref# 12 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank

70-7037 / E7037
Inner cover plate
Ref# 7 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase

70-7310 / E7310
Bin D-1 (3/0/0)
O-ring Buna-N/Dash#120/Nom.CS 3/32"/ID 1"
Ref# 6 Fig. 5 Page 21 #7 (1969) (Req:2)
Pushrod cover tube, bottom
¹ Obsolite, use 71-1283 (Viton) top & bottom

70-7351 / E7351
Bin M-6 (4/6/0)
Washer, sealing
Ref# 19 Fig. 22 Page 53 #7 (1969) (Req:2)
Gas tank, gas tap
¹ Use copper crush washers
with bonded rubber seals
Ref# 33 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach gear housing T120R-TR6R
¹ Bonded rubber

70-7354 / E7354
Bin B-5 (4/0/0)
Screw BA 2BA X 1/2 X 13/32 U.H.
Ref# 17 Fig. 6 Page 23 #7 (1969) (Req:2)
Contact breaker cover plate

70-7400 / E7400
Valve spring, outer (green spot) (Tool-Spring compressor)
Ref# 22 Fig. 5 Page 21 #7 (1969) (Req:4)
Cylinder head, valve stem

70-7471 / E7471
Nut, locking ASME 1/4-26TPI Nyloc (Tool-7/16")
Ref# 14 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust pipe bracket/exhaust pipe

70-7512 / E7512
Clip 1 3/8"
Ref# 33 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust crossover pipe (Alternate)

70-7563 / E7563
Bin D-1 (4/0/0)
O-ring Viton/Dash#20/Nom.CS 1/16"/ID 7/8"
Ref# 36 Fig. 3 Page 17 #7 (1969) (Req:2)
Tappet guide

70-7565 / E7565
Bin L-1 (3/0/0)
Oil seal (1.5"x1.06"x.25") (1-1/2"x1"x7/32" Baxter)
Ref# 8 Fig. 11 Page 33 #7 (1969) (Req:1)
Inner cover plate
Orient: Springs toward primary / (?flush on that side)

70-7573 / E7573
Bin G-4 (0/1/0)
Rubber plug
Ref# 53 Fig. 2 Page 15 #7 (1969) (Req:1)
Protection blade hole

70-7590 / E7590
Valve body (Tool-1")
Ref# 14 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil release valve

70-7591 / E7591
Spring
Ref# 18 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil release valve

70-7680 / E7680
Bolt, pillar 5/32-32TPI x 3/4 .O.A.
Ref# 12 Fig. 6 Page 23 #7 (1969) (Req:2)
Contact breaker assembly

70-8038
Shim, engine sprocket .010"
Ref# NA Fig. na Page NA
Crankshaft DS
¹ Align engine sprocket with Duplex wheel

70-8039
Shim, engine sprocket .015"
Ref# NA Fig. na Page NA
Crankshaft DS
¹ Align engine sprocket with Duplex wheel

70-8287 / E8287
Screw, slotted 2BA x 3/4 slotted (cheesehead)
Ref# 32 Fig. 35 Page 77 #7 (1969) (Req:2)
Condenser bracket to frame

70-8737 / E8737
Cover
Ref# 14 Fig. 6 Page 23 #7 (1969) (Req:1)
Contact breaker assembly

70-8751 / E8751
Bin - (1/0/0)
Hollow dowel - barrel locating dowels
Ref# 16 Fig. 2 Page 15 #7 (1969) (Req:2)
Crankcase DS forward cylinder stud 21-1865 (Fig.2 Ref.28)
¹ Incorrect PN and Qty shown in #7

70-8782 / E8782
Bin D-1 (5/0/0)
O-ring Viton/Dash#20/Nom CS 1/16"/ID 7/8"
Ref# 48 Fig. 2 Page 15 #7 (1969) (Req:2)
Primary chaincase filler plug
Ref# 48 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox filler plug
Ref# 33 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase inspection cap

70-8801 / E8801
Bin O-1 (0/0/0)
Tappet, exhaust
Ref# 35 Fig. 3 Page 17 #7 (1969) (Req:2)
Tappet guide block
Orient: Machined cutaways (oil feed hole) must face OUT.

70-8828 / E8828
Bolt UNF (SAE) 1/4-26?28?TPI x 2-3/16
(2"U.H., 3/4"thread) (Tool-1/2)
Ref# 9 Fig. 6 Page 23 #7 (1969) (Req:1)
Auto advance unit
Torque: 8 LBS

70-8860 / E8860
Washer, spherical
Ref# 9 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust pipe head clamp bolt

70-8892 / E8892
Protection blade
Ref# 51 Fig. 2 Page 15 #7 (1969) (Req:1)
Primary chaincase

70-8896 / E8896
Bin D-3 (3/0/0)
Washer, fiber 15/32"
Ref# 26 Fig. 2 Page 15 #7 (1969) (Req:1)
Tachometer drive plug
¹ Waldridge sent metal washer
Ref# 26 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase, timing hole plug

70-8992 / E8992
Bin L-7 (0/2/1)
Nut, sleeve UNC (SAE) 1/2-13TPI
Ref# 19 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase

70-9245 / E9245
Cover
Ref# 25 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase

70-9246 / E9246
Cover
Ref# 1 Fig. 6 Page 23 #7 (1969) (Req:1)
Timing chest
¹ Top, rear-most, and two
bottom-most screws are long

70-9269 / E9269
Oil pump feed plunger
Ref# 3 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil pump

70-9330 / E9330
Plug UNC (SAE) 5/16-18TPI
Ref# 23 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase oilway plug (below timing chest)

70-9331 / E9331
Tachometer gear housing
Ref# 16 Fig. 33 Page 73 #7 (1969) (Req:1)
Tachometer T120R-TR6R

70-9332 / E9332
Bin - (1/0/0)
Adapter/Securing Screw LEFT-HAND (Tool-7/16"thin/11mm)
Ref# 17 Fig. 33 Page 73 #7 (1969) (Req:1)
Tach gear housing T120R-TR6R

70-9336 / E9336
Drain plug and filter BA (Tool-13/16")
Ref# 37 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase oil drain/filter
¹ Use O-Ring 70-7310;
Replaces 70-5315 copper (TSB)

70-9348 / E9348
Bin D-6 (10/0/0)
Joint washer
Ref# 32 Fig. 5 Page 21 #7 (1969) (Req:2)
Rocker box

70-9349 / E9349
Pushrod cover tube
Ref# 5 Fig. 5 Page 21 #7 (1969) (Req:2)
Pushrod cover tube
¹ Upgraded to E12575 in 71 US (Ref#5 Fig 5)

70-9352 / E9352
Guide, tapet
Ref# 30 Fig. 3 Page 17 #7 (1969) (Req:1)
Inlet

70-9353 / E9353
Guide, tapet
Ref# 31 Fig. 3 Page 17 #7 (1969) (Req:1)
Exhaust

70-9368 / E9368
Exhaust pipe, crossover
Ref# 3 Fig. 15 Page 41 #7 (1969) (Req:1)
Exhaust

70-9418 / E9418
CYLINDER HEAD, WITH VALVE GUIDES
Ref# 8 Fig. 5 Page 21 #7 (1969) (Req:1)
Cylinder head

70-9421 / E9421
Oil pump assembly
Ref# 1 Fig. 3 Page 17 #7 (1969) (Req:1)
Timing chest

70-9488/040 / E9488
Piston, 9:1 9:1 CR. Gudgeon pin hole dia. 0.6882"-.6886"
Ref# 13 Fig. 1 Page 13 #7 (1969) (Req:2)
Piston

70-9516 / E9516
Exhaust pipe adaptor
Ref# 17 Fig. 5 Page 21 #7 (1969) (Req:2)
Exhaust

70-9525 / E9525
Connecting rod
Ref# 8 Fig. 1 Page 13 #7 (1969) (Req:2)
Con rod
¹ 70-9525 rods ('69 & on) are thicker/stronger at small end

70-9550 / E9550
Carburetter adaptor, left UNF 1-3/8" x 16 tpi.('69 and later)
Ref# 12 Fig. 5 Page 21 #7 (1969) (Req:1)
Cylinder head

70-9551 / E9551
Carburetter adaptor, right
Ref# 13 Fig. 5 Page 21 #7 (1969) (Req:1)
Cylinder head

70-9554 / E9554
Bin M-5 (4/0/0)
Insulating ring
Ref# 35 Fig. 31 Page 71 #7 (1969) (Req:4)
Carburetter
¹ Viton o-ring Dash# -202 (1/8 x 1/4 x 1/2) suitable

70-9555 / E9555
Bin M-5 (1/3/0)
Cup
Ref# 34 Fig. 31 Page 71 #7 (1969) (Req:4)
Carburetter/adapters T120R

70-9626 / E9626
Cap
Ref# 5 Fig. 15 Page 41 #7 (1969) (Req:8)
Exhaust crossover pipe clip

70-9627 / E9627
Clip
Ref# 4 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust crossover pipe

70-9686 / E9686
CRANKSHAFT AND FLYWHEEL ASSEMBLY, COMPLETE
Ref# 1 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft

70-9687 / E9687
Flywheel
Ref# 5 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft

70-9703 / E9703
Nut, sleeve (Tool-D496)
Ref# 14 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chain tensioner

70-9711 / E9711
Bin M-4 (4/0/0)
O-ring Viton/Dash#126/Nom.CS 3/32"/ID 1-3/8" (aka 'thick')
Ref# 27 Fig. 30 Page 72 PARTS 70 (Req:2)
Carburetter flange T120
Orient: Do NOT use (thin) 244/1.
¹ '69/on. No paper gasket/insulating block.

70-9722 / E9722
Bin - (0/1/1)
Exhaust pipe D.S. Crossover set
Ref# 1 Fig. 15 Page 41 #7 (1969) (Req:1)
Exhaust
¹ 70-9722='69 w/crossover; 70-5957/5958='68 wo/crossover

70-9723 / E9723
Bin - (0/1/1)
Exhaust pipe T.S.
Ref# 2 Fig. 15 Page 41 #7 (1969) (Req:1)
Exhaust

70-9748 / E9748
Crankcase D.S.
Ref# 1 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase D.S.

70-9749 / E9749
Crankcase T.S.
Ref# 8 Fig. 2 Page 15 #7 (1969) (Req:1)
Crankcase T.S.

70-9888 / E9888
Exhaust pipe crossover
Ref# 32 Fig. 15 Page 41 #7 (1969) (Req:1)
Exhaust
¹ Later models used these alternatively

71-
71-0040 / E1-0040
Camshaft, inlet, racing type
Ref# 35 Fig. 1 Page 13 #7 (1969) (Req:1)
Camshaft
¹ Same sports/racing profile as 70-3134

71-0041 / E1-0041
Camshaft, exhaust, racing type
Ref# 36 Fig. 1 Page 13 #7 (1969) (Req:1)
Camshaft
¹ Same sports/racing profile as 70-3134

71-0070 / E1-0070
Rocker ball pin
Ref# 46 Fig. 5 Page 21 #7 (1969) (Req:4)
Rocker

71-0082 / E1-0082
Bin L-2 (2/0/0)
Key Woodruff key
Ref# 22 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft/Alternator Rotor

71-0216 / E1-0216
Bin H-3 (0/2/0)
Clamp 1 3/4"
Ref# 8 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust pipe/head
¹ Use 70-8860 conical washer & 70-8860 bolt

71-1283 / E1-1283
Bin D-1 (4/0/0)
O-ring (hi-temp) Viton
Ref# XX Fig. 5 Page 21 1971 PARTS (Req:2)
Pushrod cover tube, top
¹ Updated part, replaces 70-7310 top & bottom

71-1345 / E1-1345
Bin G-4 (3/1/0)
Grommet, rubber
Ref# 20 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase, alternator leads
Orient: Outside primary chaincase
¹ Not shown/listed in #7

71-1701 / E1-1707
Sleeve (wedding band)
Ref# XX Fig. 5 Page 21 1971 PARTS (Req:2)
Pushrod cover tube, bottom
¹ Note '71US Parts source: Page/Ref 25/64

71-2660
Bin L-2 (1/1/0)
Shim, engine sprocket .030" (.0292)
Ref# NA Fig. na Page NA
Crankshaft DS
¹ Align engine sprocket with Duplex wheel

71-3748 / WE259A
Collet, split
Ref# 24 Fig. 5 Page 21 #7 (1969) (Req:8)
Cylinder head, valve stem

71-3799 / F3799 LUCAS 166043
Nut
Ref# 6 Fig. 35 Page 77 #7 (1969) (Req:4)
Ignition coil

82-
82-0879 / F879
Bin E-6 (3/0/0)
Nut CEI/BSC/Cycle 1/4-26TPI (Tool-1/4BS 3/16W open)
Ref# 34 Fig. 5 Page 21 #7 (1969) (Req:6)
Rocker box mount stud
Torque: 5 LBS
Ref# 36 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard, C-clamp
Ref# 30 Fig. 23 Page 55 #7 (1969) (Req:2)
Oil tank mount, upper
Ref# 39 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender, stud 61/38 stoplight adaptor (to fender)

82-0929 / F929
Bin H-5 (2/0/0)
Bolt CEI/BSC/Cycle 5/16-26TPI X 1/2 U.H.
Ref# 18 Fig. 15 Page 41 #7 (1969) (Req:4)
Muffler hanger bracket
¹ Hanger to muffler. Washer S26-3 Fig.15/Ref.17

82-0967 / F967
Bin G-7 (2/0/0)
Washer, rubber
Ref# 27 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank, rear mount

82-1335 / F1335
Washer, plain 5/16"
Ref# 17 Fig. 18 Page 47 #7 (1969) (Req:2)
Handlebar mount T120R-TR6R

82-1369 / F1369
Bin F-6 (2/0/0)
Bolt CEI/BSC/Cycle 1/4-26TPI x 5/8
Ref# 37 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard C-clamp

82-1694 / F1694
Passenger footrest pedal
Ref# 14 Fig. 29 Page 67 #7 (1969) (Req:2)
Passenger footrest

82-1695 / F1695
Pedal, rubber
Ref# 20 Fig. 29 Page 67 #7 (1969) (Req:2)
Passenger footrest

82-1713 / F1713
Bin D-3 (2/0/0)
Washer, fiber
Ref# 7 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank filter

82-1747 / F1747
Nut, plain UNF (SAE) 3/4"; .436" (7/16") thick; 1.099" (<1-7/64") across flats
Ref# 44 Fig. 20 Page 51 #7 (1969) (Req:2)
Rear wheel spindle, T.S./D.S. (outside)
Torque: 90 LBS
¹ Outside nuts on T.S./D.S.

82-1880 / F1880
Bin D-4 (5/0/0)
Washer, copper oilway plug 5/16"
Ref# 24 Fig. 2 Page 15 #7 (1969) (Req:1)
Oilway plug 70-9330 Fig.2 Ref.23
Ref# 37 Fig. 11 Page 33 #7 (1969) (Req:2)
Primary chaincase cover (stator studs)

82-2184 / F2184
Washer, plain 3/8
Ref# 26 Fig. 5 Page 21 #7 (1969) (Req:8)
Cylinder head bolt

82-2277 / F2277
Washer, spring 5/16" double coil
Ref# 18 Fig. 29 Page 67 #7 (1969) (Req:2)
Passenger footrest

82-2351 / F2351
Washer, plain
Ref# 39 Fig. 19 Page 49 #7 (1969) (Req:3)
Front brake air scoop

82-2725 / F2725
Bin P-1 (1/3/0)
Nut, locking BSPP
Ref# 9 Fig. 12 Page 43 #4 (Req:2)
Center stand '64-'68 650
¹ Goes with '65-'68 center stands (82-5932)

82-3069 / F3069
Bin C-9 (2/0/0)
Distance piece 1/4" thick
Ref# 32 Fig. 14 Page 39 #7 (1969) (Req:4)
Engine torque stays

82-3098 / F3098
Clip, oil tank breather
Ref# 19 Fig. 23 Page 55 #7 (1969) (Req:2)
Oil tank breather

82-3158 / F3158 LUCAS 315738
Bin A-3 (1/0/0)
Spring
Ref# 47 Fig. 13 Page 37 #7 (1969) (Req:1)
Brakelight switch

82-3179 / F3179
Filter (Tool-1")
Ref# 6 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank

82-3182 / F3182
Nut, union (Tool-3/8BS 5/16W)
Ref# 9 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank pipe, filter

82-3220 / F3220
Filler cap
Ref# 13 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank

82-3655 / F3655
Pipe, feed
Ref# 8 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank pipe, filter

82-3799 / F3799
Bin B-4 (3/4/0)
Nut
Ref# 37 Fig. 26 Page 61 #7 (1969) (Req:1)
Stoplight
Ref# 35 Fig. 35 Page 77 #7 (1969) (Req:2)
Condenser bracket
Ref# 38 Fig. 35 Page 77 #7 (1969) (Req:3)
Horn mount

82-3808 / F3808
C-clamp
Ref# 35 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard to torque stay
Orient: C-clamp goes on top of chain guard bracket

82-3814 / F3814
Bin G-8 (3/1/0)
Cup
Ref# 23 Fig. 22 Page 53 #7 (1969) (Req:3)
Gas tank, front tank mount

82-4019 / F4019
Washer, serrated
Ref# 11 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank, center styling strip

82-4047 / F4047
Bin J-3 (4/0/0)
Washer, cork 2"
Ref# 19 Fig. 17 Page 45 #7 (1969) (Req:2)
Spring abutment, stanchion tube
¹ Oil tank cap also (Fig.23 Ref.3)
Ref# 3 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank filler cap
¹ Also 45/19 fork spring abutment

82-4048 / F4048
Bin M-6 (1/1/1)
Joint washer 2 1/2"
Ref# 15 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank filler cap

82-4228 / F4228
Spring
Ref# 18 Fig. 25 Page 59 #7 (1969) (Req:1)
Seat latch

82-4299 / F4299
Bin - (2/0/0)
Washer, plain 5/16" large O.D.
Ref# 26 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, bracket (R#5) to lower fork leg

82-4370 / F4370
Bin C-9 (4/3/2)
Washer, plain 7/16 x 15/16
Ref# 20 Fig. 12 Page 35 #7 (1969) (Req:2)
Main/rear frame (bottom front, for nut 35/21)
Ref# 42 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine mounting stud (when bash plate fitted)
¹ Stud Ref.4

82-4483 / F4483
Screw, self-tapping 1/2" self-tapping Philips
Ref# 16 Fig. 25 Page 59 #7 (1969) (Req:1)
Seat check wire

82-4484 / F4484
Bin P-1 (2/1/0)
Washer, tab 1/2"ID "D"-shaped double-tab
Ref# 8A Fig. 12 Page 43 #4 (Req:2)
Center stand '64-'68 650
¹ Goes with '65-'68 center stands (82-5932)

82-4671 / F4671
Bin P-3 (2/0/0)
Spring, return
Ref# 10 Fig. 12 Page 35 #7 (1969) (Req:1)
Center stand

82-4715 / F4715
Screw, Phillips BA 2BA X 13/32
Ref# 35 Fig. 26 Page 61 #7 (1969) (Req:3)
Rear fender, tail light plate (to adaptor)

82-4717 / F4717
Bin A-3 (1/0/0)
Nut, locking BA 2BA
Ref# 44 Fig. 13 Page 37 #7 (1969) (Req:3)
Brakelight switch
¹ #7 says Qty.5 (p.37) Only find 3
Ref# 44 Fig. 13 Page 37 #7 (1969) (Req:1)
Brakelight switch lever

82-4771 / F4771
Screw BA 2BA X 1/2 (3/8 in. U.H.)
Ref# 37 Fig. 35 Page 77 #7 (1969) (Req:2)
Horn mounting

82-4810 / F4810
Bin M-8 (2/1/1)
Clip with screw and nut
Ref# NI Fig. 24 Page 57 #7 (1969) (Req:2)
Air cleaner cover
¹ Not illustrated in Fig 24

82-4971 / F4971
Gas tap BSPP 1/4 BSPP - 0.518"O.D. 19 TPI
Ref# 16 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank D.S.

82-4972 / F4972
Bin M-6 (1/2/0)
Gas tap W/Tube BSPP 1/4 BSPP - 0.518"O.D. 19 TPI
Ref# 17 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank

82-5228 / F5228
Bin G-7 (4/2/0)
Washer, rubber
Ref# 21 Fig. 22 Page 53 #7 (1969) (Req:2)
Gas tank, front tank mount

82-5229 / F5229
Bin G-7 (5/0/0)
Spigot, rubber
Ref# 22 Fig. 22 Page 53 #7 (1969) (Req:2)
Gas tank front mount

82-5313 / F5313
Distance tube
Ref# 6 Fig. 13 Page 37 #7 (1969) (Req:1)
Swinging fork

82-5336 / F5336
Bin G-7 (2/0/0)
Spigot, rubber, double
Ref# 26 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank rear mount

82-5338 / F5338
Nut ASME 1/4-26TPI
Ref# 41 Fig. 35 Page 77 #7 (1969) (Req:1)
Selenium rectifier mount

82-5343 / F5343
Plug BSPP (Tool-7/16BS 3/8W)
Ref# 4 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank drain plug

82-5412 / F5412
Bin A-3 (1/0/0)
Switch lever
Ref# 45 Fig. 13 Page 37 #7 (1969) (Req:1)
Rear brakelight switch

82-5413 / F5413
Bin A-3 (1/0/0)
Washer, D
Ref# 46 Fig. 13 Page 37 #7 (1969) (Req:1)
Brakelight switch

82-5469 / F5469
Stud, engine mtg/crankcase junction ASME 7/16-26TPI X 3-5/16 O.A.
Ref# 1 Fig. 14 Page 39 #7 (1969) (Req:1)
Engine/frame
¹ Crankcase junction stud #1

82-5532 / F5532
Bin C-9 (2/0/0)
Distance piece
Ref# 5 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine mount stud (bottom)
¹ Spacers go btwn engine and frame

82-5536 / F5536
Grommet
Ref# 27 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard chain inspection port

82-5678 / F5678
Bin P-1 (1/3/0)
Bolt, pivot UNF (SAE) 1/2-20TPI
Ref# 7 Fig. 12 Page 43 #4 (Req:2)
Center stand '64-'68 650
¹ This part for '65-'68 center stand (82-5932)

82-5679 / F5679
Bin P-2 (2/2/0)
Washer, plain 1/2"ID x 7/8" x 3/32"
Ref# 8 Fig. 12 Page 35 #7 (1969) (Req:2)
Center stand '64-'68 650
¹ Fits '65-'68 82-5932 & '69-'70 83-1267 center stands

82-5692 / F5932
Center stand (1968) 10-1/8" height
Ref# 5 Fig. 34 Page 34 #6 (1968) (Req:1)
Frame, rear

82-5764 / F5764
Air cleaner element (cloth and gauze) 1 5/8" thick
Ref# 10 Fig. 24 Page 57 #7 (1969) (Req:2)
Air cleaner T120R

82-5908 / F5908
Engine plate
Ref# 7 Fig. 14 Page 39 #7 (1969) (Req:1)
T.S. rear

82-5943 / F5943
Locating peg
Ref# 19 Fig. 14 Page 39 #7 (1969) (Req:4)
Driver footrests

82-5944 / F5944
Bin J-9 (3/3/0)
Washer, tab
Ref# 9 Fig. 13 Page 37 #7 (1969) (Req:1)
Swinging fork

82-5994 / F5994
Clip
Ref# 10 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender to rear frame

82-6031 / F6031
Backing plate
Ref# 11 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear frame clip

82-6039 / F6039
Bin G-5 (1/0/0)
Grommet, rubber
Ref# 36 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank mount, lower

82-6042 / F6042
Bin - (4/0/0)
Bush, pivot Pre-sized. Bush bore diameter: 1.4460"-1.4470"
Ref# 2 Fig. 13 Page 37 #7 (1969) (Req:2)
Swinging fork

82-6064 / F6064
Brake pedal lever
Ref# 33 Fig. 14 Page 39 #7 (1969) (Req:1)
Brake pedal

82-6066 / F6066
Engine plate
Ref# 6 Fig. 14 Page 39 #7 (1969) (Req:1)
D.S. rear

82-6147 / F6147
Bracket
Ref# 35 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank mount, lower

82-6310 / F6310
Bin C-9 (4/0/0)
Washer, plain
Ref# 30 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender, frame bracket
Ref# 30 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear frame, bridge (bolt head)

82-6449 / F6449
Brake pedal
Ref# 36 Fig. 14 Page 39 #7 (1969) (Req:1)
Engine plate D.S.

82-6498 / F6498
Stud, engine mtg/crankcase junction ASME 7/16-26TPI X 8-1/16 O.A.
Ref# 4 Fig. 14 Page 39 #7 (1969) (Req:1)
Engine/frame
¹ Crankcase junction stud #6

82-6511 / F6511
Screw, metering
Ref# 26 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank, for chain lube

82-6673 / F6673
Bin G-5 (1/1/0)
Spigot, rubber
Ref# 22 Fig. 23 Page 55 #7 (1969) (Req:4)
Oil tank mount and battery holder
Ref# 5 Fig. 25 Page 59 #7 (1969) (Req:1)
Side panel

82-6738 / F6738
Lock, steering
Ref# 10 Fig. 17 Page 45 #7 (1969) (Req:1)
Upper yoke

82-6821 / F6821
Sleeve Diameter: 1.4445"-1.4450"
Ref# 5 Fig. 13 Page 37 #7 (1969) (Req:2)
Swinging fork

82-6849 / F6849
Stoplight plate
Ref# 13 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender

82-6850 / F6850
Bracket
Ref# 14 Fig. 26 Page 61 #7 (1969) (Req:1)
Liscense plate

82-6851 / F6851
Bracket
Ref# 9 Fig. 26 Page 61 #7 (1969) (Req:1)
Stoplight

82-6874 / F6874
Spring
Ref# 27 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank chain oiler metering screw 55/26

82-6915 / F6915
Bridge
Ref# 7 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender beneath seat
Orient: Bridge fits inside rear frame loop.

82-6943 / F6943
Bin B-4 (0/1/1)
Bracket, ignition coil (left)
Ref# 20 Fig. 35 Page 77 #7 (1969) (Req:1)
Frame T120R-TR6C

82-6944 / F6944
Bin B-4 (0/1/1)
Bracket, ignition coil (right)
Ref# 21 Fig. 35 Page 77 #7 (1969) (Req:1)
Frame T120R-TR6C

82-6968 / F6968
Bin P-9 (2/0/0)
Washer, rubber
Ref# 23 Fig. 23 Page 55 #7 (1969) (Req:2)
Battery holder straps, front/rear

82-6981 / F6981
Lock, with keys
Ref# 32 Fig. 36 Page 79 #7 (1969) (Req:1)
Ignition switch T120R-TR6R

82-7021 / F7021
Bin P-3 (1/0/0)
Bolt, pivot
Ref# 12 Fig. 12 Page 35 #7 (1969) (Req:1)
Side stand

82-7067 / F7067
Chainguard
Ref# 26 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard

82-7155 / F7155
Bin I-2 (2/0/0)
Steering stop UNF (SAE) 3/8" UNF 24 TPI
Ref# 24 Fig. 12 Page 35 #7 (1969) (Req:2)
Frame, front

82-7352 / F7352
Tubing, flexible pipe
Ref# 38 Fig. 23 Page 55 #7 (1969) (Req:1)
Froth tower
¹ Chain oiler connecting tube

82-7353 / F7353
Tubing, extension pipe
Ref# 18 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank Tee 70-5370
¹ Vents oil tank & crankcase to back of rear fender

82-7364 / F7364
Rubber tube
Ref# 29 Fig. 13 Page 37 #7 (1969) (Req:1)
Chain oiler

82-7365 / F7365
Torque stay, rear brake
Ref# 11 Fig. 13 Page 37 #7 (1969) (Req:1)
Swinging fork

82-7386 / F7386
Brake operating rod
Ref# 39 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard

82-7387 / F7387
Bin I-9 (2/0/0)
Nut, sleeve UNF (SAE) 1/4-28TPI
Ref# 41 Fig. 13 Page 37 #7 (1969) (Req:1)
Brake operating rod adjustment

82-7388 / F7388
Bin M-7 (1/1/0)
Bolt ?-?TPI X 1-17/32 U.H.
Ref# 28 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank rear mount

82-7389 / F7389
Nut (Tool-3/4)
Ref# 41 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine mount plates, stud 39/21
Torque: 100 LBS

82-7431 / F7431
Pipe, vent
Ref# 6 Fig. 24 Page 57 #7 (1969) (Req:1)
Battery

82-7510 / F7510
Screwed peg
Ref# 28 Fig. 23 Page 55 #7 (1969) (Req:2)
Oil tank shock mounting

82-7560 / F7560
Seat catch plunger
Ref# 20 Fig. 25 Page 59 #7 (1969) (Req:1)
Seat latch

82-7582 / F7582
Bin P-7 (0/1/1)
Relay stay
Ref# 58 Fig. 35 Page 77 #7 (1969) (Req:1)
Horn relay bracket

82-7826 / F7826
Wiring protector
Ref# 18 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender

82-7835 / F7835
Bin G-6 (4/0/0)
Rubber buffer
Ref# 10 Fig. 25 Page 59 #7 (1969) (Req:4)
Seat

82-7836 / F7836
Bin - (0/1/0)
Oil tank
Ref# 1 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank

82-7843 / F7843
Front frame
Ref# 1 Fig. 12 Page 35 #7 (1969) (Req:1)
Frame

82-7848 / F7848
Bin J-9 (1/0/0)
Washer, flanged
Ref# 7 Fig. 13 Page 37 #7 (1969) (Req:2)
Swinging fork

82-7849 / F7849
Side stand
Ref# 11 Fig. 12 Page 35 #7 (1969) (Req:1)
Frame, front

82-7860 / F7860
Lifting handle
Ref# 8 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender

82-7862 / F7862
Hinge
Ref# 12 Fig. 25 Page 59 #7 (1969) (Req:1)
Seat, rear hinge

82-7888 / F7888
Bin M-7 (1/2/2)
Screw, Phillips BA 2BA X 3/8 chrome Phillips (Tool-Phillips)
Ref# 6 Fig. 22 Page 53 #7 (1969) (Req:2)
Gas tank styling unit (rear)

82-7892 / F7892
Circlip
Ref# 7 Fig. 24 Page 57 #7 (1969) (Req:1)
Battery vent pipe

82-8024 / F8024
Bin - (0/1/0)
Battery holder
Ref# 1 Fig. 24 Page 57 #7 (1969) (Req:1)
Battery holder

82-8026 / F8026
Hinge
Ref# 11 Fig. 25 Page 59 #7 (1969) (Req:1)
Seat, front hinge

82-8028 / F8028
Bin - (0/1/1)
Strap, battery holder
Ref# 21 Fig. 23 Page 55 #7 (1969) (Req:1)
Battery holder, rear

82-8031 / F8031
Rubber strip
Ref# 5 Fig. 24 Page 57 #7 (1969) (Req:2)
Battery holder

82-8032 / F8032
Anchor, battery strap
Ref# 4 Fig. 24 Page 57 #7 (1969) (Req:1)
Battery holder

82-8033 / F8033
Bin G-8 (1/1/0)
Strap, battery holder
Ref# 3 Fig. 24 Page 57 #7 (1969) (Req:1)
Battery holder

82-8034 / F8034
Bin E-6 (4/0/0)
Nut, sleeve UNF (SAE) 1/4-28TPI (Tool-9/16")
Ref# 40 Fig. 23 Page 55 #7 (1969) (Req:1)
Battery holder strap, front (common connection)

82-8036 / F8036
Rear frame
Ref# 15 Fig. 12 Page 35 #7 (1969) (Req:1)
Frame

82-8042 / F8042
Bin - (0/1/0)
Side panel and toolbox
Ref# 1 Fig. 25 Page 59 #7 (1969) (Req:1)
Side panel

82-8082 / F8082 LUCAS 54418528
Bin - (0/0/1)
Bracket
Ref# 31 Fig. 35 Page 77 #7 (1969) (Req:1)
Condenser pack

82-8090 / F8090
Bin J-9 (2/0/0)
O-ring Viton/Dash#224/Nom. 1-3/4 X 2 X 1/8
Ref# 15 Fig. 13 Page 37 #7 (1969) (Req:2)
Swinging fork

82-8091 / F8091
Tray, rubber
Ref# 2 Fig. 24 Page 57 #7 (1969) (Req:1)
Battery holder

82-8133 / F8133
Gas pipe
Ref# 28 Fig. 31 Page 71 #7 (1969) (Req:1)
Carburetter T120R
Orient: Accute angle of pipes goes forward

82-8139 / F8139
Stoplight body (adaptor)
Ref# 12 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender

82-8140 / F8140
Rubber mat
Ref# 17 Fig. 26 Page 61 #7 (1969) (Req:2)
Stoplight reflector

82-8143 / F8143
Bin - (0/1/1)
Fender, painted
Ref# 6 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender T120R-TR6R

82-8192 / F8192
Bin S-1 (0/1/1)
Knee grip, left
Ref# 7 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank

82-8193 / F8193
Bin S-1 (0/1/1)
Knee grip, right
Ref# 8 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank

82-8194 / F8194
Bin - (0/0/2)
Bracket, reflector
Ref# 29 Fig. 22 Page 53 #7 (1969) (Req:2)
Gas tank

82-8195 / F8195
Push fix
Ref# 16 Fig. 26 Page 61 #7 (1969) (Req:4)
Stoplight reflectors

82-8196 / F8196
Bin S1- (0/3/3)
Air cleaner cover
Ref# 9 Fig. 24 Page 57 #7 (1969) (Req:2)
Air cleaner T120R

82-8245 / F8245
Washer, starlock
Ref# 48 Fig. 17 Page 45 #7 (1969) (Req:1)
Brake cable, front brake

82-8392 / F8392
Bin P-3 (1/0/0)
Spring
Ref# 14 Fig. 12 Page 35 #7 (1969) (Req:1)
Side stand return

82-9255 / F9255
Bin - (0/1/1)
Strap, battery holder
Ref# 20 Fig. 23 Page 55 #7 (1969) (Req:1)
Battery holder, front

82-9279 / NF704
Bin - (1/0/0)
Footpeg rubber
Ref# 20 Fig. 14 Page 39 #7 (1969) (Req:2)
Driver footrests

82-9369 / F9369
PASSENGER FOOTREST ASSEMBLY
Ref# 13 Fig. 29 Page 67 #7 (1969) (Req:2)
Passenger footrest

82-9370 / F9370
Hanger, passenger footrest
Ref# 15 Fig. 29 Page 67 #7 (1969) (Req:2)
Passenger footrest

82-9371 / F9371
Bolt, pivot
Ref# 17 Fig. 29 Page 67 #7 (1969) (Req:2)
Passenger footrests

82-9387 / F9387
Bin F-6 (1/0/0)
Bolt, stepped
Ref# 32 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard, rear mount

82-9498 / F9498
Seat rail
Ref# 21 Fig. 25 Page 59 #7 (1969) (Req:1)
Seat

82-9624 / F9624
Footrest, driver, right
Ref# 15 Fig. 14 Page 39 #7 (1969) (Req:1)
Engine mount plate

82-9659 / F9659
Filler cap
Ref# 2 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank

82-9702 / F9702
Gas tank (2 1/2 gallons)
Ref# 2 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank T120R

82-9714 / F9714
Bin - (0/1/1)
Seat
Ref# 6 Fig. 25 Page 59 #7 (1969) (Req:1)
Seat

82-9715 / F9715
Seat cover
Ref# 7 Fig. 25 Page 59 #7 (1969) (Req:1)
Seat

82-9736 / F9736
Footrest, driver, left
Ref# 14 Fig. 14 Page 39 #7 (1969) (Req:1)
Engine mount plate

83-
83-0002 / F10002
Washer, steel 1/2" x 7/8" x .036"
Ref# 20 Fig. 22 Page 53 #7 (1969) (Req:2)
Gas tank, gas tap

83-0006 / F10006
Bin M-6 (1/0/0)
Nut UNC (SAE) 1/2 x 13TPI (Tool-7/16BS 3/8W)
Ref# 18 Fig. 22 Page 53 #7 (1969) (Req:2)
Gas tank, gas tap

83-0008 / F10008
Screw, hook
Ref# 10 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank, center styling strip

83-0031 / F10031
Center styling strip
Ref# 9 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank

83-0033 / F10033
Bin B-2 (0/2/2)
Screw, Phillips 10-32UNF x 3/8, Phillips
Ref# 33 Fig. 35 Page 77 #7 (1969) (Req:2)
Condenser bracket, condenser to bracket

83-0045 / F10045
Swinging fork
Ref# 1 Fig. 13 Page 37 #7 (1969) (Req:1)
Swinging fork
¹ Grease@1,000 mi.intervals

83-0222 / F10222
Bin P-4 (1/0/0)
Nut, panel
Ref# 4 Fig. 25 Page 59 #7 (1969) (Req:1)
Side panel

83-1254 / F11254
Bin P-8 (0/0/1)
Bracket
Ref# 57 Fig. 35 Page 77 #7 (1969) (Req:1)
Horn relay

83-1267 / F11267
Bin - (0/0/1)
Center stand (1969) 10-1/8" height
Ref# 5 Fig. 12 Page 35 #7 (1969) (Req:1)
Center stand

83-1270 / F11270
Bin P-2 (5/0/0)
Washer, tab 7/16"ID "D"-shaped double-tab
Ref# 8A Fig. 12 Page 35 #7 (1969) (Req:2)
Center stand '69/'70 650
¹ Goes with '69-'70 center stands (83-1267)

83-1339 / F11339
Bin M-7 (3/1/0)
Screw BA 2BA X 3/4
Ref# 5 Fig. 22 Page 53 #7 (1969) (Req:2)
Gas tank styling unit (front)

83-1340 / F11340
Bin S1- (0/1/1)
Styling unit (badge) left
Ref# 3 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank

83-1341 / F11341
Bin S1- (0/1/1)
Styling unit (badge) right
Ref# 4 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank

83-1357 / F11357
Knob
Ref# 2 Fig. 25 Page 59 #7 (1969) (Req:1)
Side panel

83-1377 / F11377
Bin P-4 (3/0/0)
Washer, rubber
Ref# 3 Fig. 25 Page 59 #7 (1969) (Req:1)
Side panel

842183
Bin B-3 (0/2/0)
Wire, high tension
Ref# 50 Fig. 35 Page 77 #7 (1969) (Req:2)
Spark plug

862217
Grommet, rubber
Ref# 12 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell T120R-TR6R

97-
97-0095 / H95
Washer, star (spring)
Ref# 10 Fig. 18 Page 47 #7 (1969) (Req:1)
Steering damper

97-0111 / H111
Steering race cups
Ref# 2 Fig. 12 Page 35 #7 (1969) (Req:2)
Frame, front

97-0200 / H200
Bolt (tappet guide)
Ref# 33 Fig. 3 Page 17 #7 (1969) (Req:2)
Tappet guide set bolt

97-0408 / H408
Adjuster sleeve
Ref# 9 Fig. 18 Page 47 #7 (1969) (Req:1)
Steering damper

97-0430 / H430
Bin J-5 (4/0/0)
Washer, fiber 3/16"
Ref# 40 Fig. 17 Page 45 #7 (1969) (Req:2)
Lower fork leg drain plug

97-0431 / H431
Washer, plain
Ref# 27 Fig. 17 Page 45 #7 (1969) (Req:2)
Stanchion tube, above top bearing

97-0435 / H435
Bin - (0/1/0)
Friction disk
Ref# 14 Fig. 18 Page 47 #7 (1969) (Req:1)
Steering damper

97-0439 / H439
Bin - (1/0/0)
Bottom cone
Ref# 3 Fig. 17 Page 45 #7 (1969) (Req:1)
Lower yoke and stem

97-0441 / H441
Bin J-6 (0/2/2)
Bearing, telescopic front fork (upper)
Ref# 28 Fig. 17 Page 45 #7 (1969) (Req:2)
Stanchion tube

97-0443 / H443
Bin - (0/2/0)
Bearing, telescopic front fork (lower)
Ref# 31 Fig. 17 Page 45 #7 (1969) (Req:2)
Stanchion tube

97-0519A / H519A
Bin J-5 (0/2/0)
Drain plug UNF (SAE) 10-32 X 1/8
Ref# 39 Fig. 17 Page 45 #7 (1969) (Req:2)
Lower fork leg

97-0565 / H565
Bin I-2 (1/0/0)
Washer, ring
Ref# 8 Fig. 18 Page 47 #7 (1969) (Req:1)
Steering damper

97-0919 / H919
Nut BA 4BA
Ref# 12 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank, center styling strip

97-1018 / H1018
Bin - (1/0/0)
Top cone and dust cover
Ref# 4 Fig. 12 Page 35 #7 (1969) (Req:1)
Steering races

97-1062 / H1062
Bin J-4 (4/0/0)
Washer, aluminum
Ref# 44 Fig. 17 Page 45 #7 (1969) (Req:2)
Lower fork leg

97-1142 / H1142
Steering damper rod with knob
Ref# 7 Fig. 18 Page 47 #7 (1969) (Req:1)
Steering damper

97-1425 / H1425
Bin I-1 (4/0/0)
Shims
Ref# 2 Fig. 27 Page 63 #7 (1969) (Req:4)
Handlebars, eyebolts 47/16 T120R-TR6R

97-1500 / H1500
Bin J-1 (4/0/0)
Oil seal
Ref# 25 Fig. 17 Page 45 #7 (1969) (Req:2)
Stanchion tube
Orient: Open lip/springs go down (to threaded end of seal holder)

97-1527 / H1527
Bin I-1 (1/0/0)
Bush, bonded
Ref# 9 Fig. 17 Page 45 #7 (1969) (Req:2)
Handle bar mounting

97-1529 / H1529
Bin I-1 (1/4/0)
Washer, hemispherical 7/8"OD, 3/8"ID - hemi
Ref# 19 Fig. 18 Page 47 #7 (1969) (Req:4)
Handlebar mount T120R-TR6R

97-1580 / H1580
Bin I-1 (4/3/0)
Steady rubber
Ref# 21 Fig. 18 Page 47 #7 (1969) (Req:2)
Handlebar mount T120R-TR6R

97-1581 / H1581
Bin I-1 (2/2/0)
Distance piece
Ref# 22 Fig. 18 Page 47 #7 (1969) (Req:2)
Handlebar mount T120R-TR6R
¹ Bush inside 97-1580 steady rubber

97-1616 / H1616
Bush, solid
Ref# 24 Fig. 18 Page 47 #7 (1969) (Req:4)
Handlebar mount T120R-TR6R
¹ For solid mount only

97-1618 / H1618
Bin I-2 (1/0/0)
Rubber sleeve
Ref# 13 Fig. 18 Page 47 #7 (1969) (Req:1)
Steering damper

97-1656 / H1656
Bin J-3 (2/0/0)
Washer, plain ID 1-7/16" OD 2"
Ref# 22 Fig. 17 Page 45 #7 (1969) (Req:2)
Fork seal holder

97-1657 / H1657
Abutment
Ref# 20 Fig. 17 Page 45 #7 (1969) (Req:2)
Stanchion tube spring

97-1685 / H1685
Bracket
Ref# 5 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender stay to fork leg
Orient: Brackets face forward, angle projects up. Stay go outside.

97-1797 / H1797
Anchor plate
Ref# 11 Fig. 18 Page 47 #7 (1969) (Req:1)
Steering damper

97-1844 / H1844
Spindle cap
Ref# 36 Fig. 17 Page 45 #7 (1969) (Req:2)
Lower fork leg

97-1870 / H1870
Bin - (1/1/1)
Handlebars, US Bonneville pre-71
Ref# 1 Fig. 27 Page 63 #7 (1969) (Req:1)
Front forks T120R-TR6R
¹ In stock: 97-1871 UK Twin 65-70

97-1891 / H1891
Bin S-T (0/4/2)
Spring Solo (Yellow/Blue)
Ref# 21 Fig. 17 Page 45 #7 (1969) (Req:2)
Front fork

97-1892 / H1892
Main spring
Ref# 21 Fig. 17 Page 45 #7 (1969) (Req:2)
Extra strong (Yellow/Green)

97-1896 / H1896
Bin J-7 (0/2/2)
Sleeve, damping
Ref# 29 Fig. 17 Page 45 #7 (1969) (Req:2)
Stanchion tube
Orient: Built-up ends of PVC damping sleeves go DOWN.

97-1929 / H1929
Bushing
Ref# 5 Fig. 33 Page 73 #7 (1969) (Req:2)
Speedo/tach mounting brackets

97-1932 / H1932
Bin A-6 (3/0/0)
Distance piece 5/16"
Ref# 20 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlamp shell T120R-TR6R

97-1946 / H1946
Mounting bracket, speedo/tach
Ref# 4 Fig. 33 Page 73 #7 (1969) (Req:1)
Speedometer

97-1994 / H1994
Screw, self-tapping 6-32 X 1/2
Ref# 37 Fig. 27 Page 63 #7 (1969) (Req:2)
Horn and dip switch

97-2090 / H2090
Restrictor (Tool-5/8)
Ref# 43 Fig. 17 Page 45 #7 (1969) (Req:2)
Lower fork leg
¹ Use speed wrench with
Extension & 5/8" socket on 45/45

97-2091 / H2091
Nut, bearing
Ref# 32 Fig. 17 Page 45 #7 (1969) (Req:2)
Bottom of stanchion tube

97-2092 / H2092
Stanchion tube
Ref# 30 Fig. 17 Page 45 #7 (1969) (Req:2)
Front forks

97-2107 / H2107
Bin I-2 (0/0/0)
Locating pin
Ref# 14 Fig. 17 Page 45 #7 (1969) (Req:1)
Lower yoke
¹ Secures steering damper if fitted

97-2108 / H2108
Bin I-2 (1/1/1)
Nut, sleeve (fork stem)
Ref# 12 Fig. 18 Page 47 #7 (1969) (Req:1)
Front forks TR6C
¹ Replaces 97-2263 for damper

97-2119 / H2119
Bin J-2 (6/2/0)
O-ring Viton/Dash#130/Nom.CS 3/32"/ID 1-5/8"
Ref# 26 Fig. 17 Page 45 #7 (1969) (Req:2)
Lower fork leg, dust excluder sleeve nut

97-2125 / H2125
Twin rotor twistgrip, grip
Ref# 37 Fig. 28 Page 65 #7 (1969) (Req:1)
Twistgrip T120R

97-2126 / H2126
Bin J-4 (0/2/2)
Bolt, flanged (Tool-5/16)
Ref# 45 Fig. 17 Page 45 #7 (1969) (Req:2)
Lower fork leg

97-2127 / H2127
Bin J-5 (2/1/0)
Circlip
Ref# 42 Fig. 17 Page 45 #7 (1969) (Req:2)
Front fork shuttle valve

97-2154 / H2154
Shuttle valve
Ref# 41 Fig. 17 Page 45 #7 (1969) (Req:2)
Stanchion tube

97-2161 / H2161
Fork cover, top left
Ref# 17 Fig. 17 Page 45 #7 (1969) (Req:1)
Stanchion tube

97-2162 / H2162
Fork cover, top right
Ref# 18 Fig. 17 Page 45 #7 (1969) (Req:1)
Stanchion tube

97-2221 / H2221
Bin I-1 (1/3/0)
Cup
Ref# 23 Fig. 18 Page 47 #7 (1969) (Req:2)
Handlebar mount T120R-TR6R

97-2236 / H2236
Bin A-1 (0/1/1)
Bracket, Zener diode
Ref# 44 Fig. 35 Page 77 #7 (1969) (Req:1)
Front forks

97-2237 / H2237
Bin A-1 (0/1/1)
Heat sink
Ref# 42 Fig. 35 Page 77 #7 (1969) (Req:1)
Zener diode

97-2245 / H2245
Nut 1 1/2" across flats
Ref# 33 Fig. 17 Page 45 #7 (1969) (Req:2)
Stanchion tube cap
Torque: 80 LBS

97-2262 / H2262
Cover, rubber
Ref# 34 Fig. 36 Page 79 #7 (1969) (Req:1)
Ignition switch T120R-TR6R

97-2263 / H2263
Bin I-2 (0/1/1)
Nut, sleeve (fork stem)
Ref# 7 Fig. 17 Page 45 #7 (1969) (Req:1)
Front forks

97-2266 / H2266
Bin I-2 (2/0/0)
Washer, sealing
Ref# 13 Fig. 17 Page 45 #7 (1969) (Req:1)
Upper yoke
¹ Steering lock

97-2270 / H2270
Cable retainer
Ref# 47 Fig. 17 Page 45 #7 (1969) (Req:1)
Brake cable, front brake

97-2275 / H2275
Plug
Ref# 48 Fig. 35 Page 77 #7 (1969) (Req:1)
Zener diode heat sink plug

97-2288 / H2288
Lower yoke and stem
Ref# 2 Fig. 17 Page 45 #7 (1969) (Req:1)
Front forks T120R

97-2290 / H2290
Bolt, pinch UNF (SAE) 3/8-24TPI X 2-1/4 U.H. (Tool-9/16)
Ref# 4 Fig. 17 Page 45 #7 (1969) (Req:2)
Stanchion tube
Torque: 25 LBS

97-2291 / H2291
Handlebar eyebolt
Ref# 16 Fig. 18 Page 47 #7 (1969) (Req:2)
Handlebars T120R-TR6R

97-2294 / H2294
Lower fork leg, left
Ref# 34 Fig. 17 Page 45 #7 (1969) (Req:1)
Front forks
¹ 1/3 pint (200cc) oil

97-2295 / H2295
Lower fork leg, right
Ref# 35 Fig. 17 Page 45 #7 (1969) (Req:1)
Front forks
¹ 1/3 pint (200cc) oil

97-3633 / H3633
Dust excluder sleeve nut (Tool-61-6017)
Ref# 24 Fig. 17 Page 45 #7 (1969) (Req:2)
Lower fork leg

97-3635 / H3635
Bin S1- (0/1/0)
Gaiter, front forks
Ref# 23 Fig. 17 Page 45 #7 (1969) (Req:2)
Stanchion tube
Orient: End with pin hole goes DOWN.

97-3658 / H3658
FORK ASSEMBLY
Ref# 1 Fig. 17 Page 45 #7 (1969) (Req:1)
Front forks T120R

97-3663 / H3663
Stay, front
Ref# 2 Fig. 26 Page 61 #7 (1969) (Req:1)
Front fender T120R-TR6R
Orient: In->Out: bolt,bracket,top stay,front stay,flat washer,nut

97-3664 / H3664
Stay, center
Ref# 3 Fig. 26 Page 61 #7 (1969) (Req:1)
Front fender T120R-TR6R
Orient: In->Out: bolt,bracket,top stay,front stay,flat washer,nut

97-3667 / H3667
Upper yoke
Ref# 8 Fig. 17 Page 45 #7 (1969) (Req:1)
Front forks

97-3668 / H3668
Stay, bottom
Ref# 4 Fig. 26 Page 61 #7 (1969) (Req:1)
Front fender T120R-TR6R
Orient: Rear bracket faces up, arms sweep up to lower legs

97-3677 / H3677
Bin - (0/1/1)
Fender, painted
Ref# 1 Fig. 26 Page 61 #7 (1969) (Req:1)
Front fender

97-3682 / H3682
Bin I-6 (0/1/0)
Bracket
Ref# 46 Fig. 17 Page 45 #7 (1969) (Req:1)
Brake cable, front brake

97-408 / H408
Nut, sleeve
Ref# 12 Fig. 18 Page 47 #7 (1969) (Req:1)
Steering damper

99-
99- LUCAS 57161
Bin P-6 (0/0/2)
Reflector, Amber
Ref# 30 Fig. 22 Page 53 #7 (1969) (Req:2)
Gas tank

99-0107 FROM I-NET 9054/171
Clips, retainer
Ref# 19 Fig. 13 Page 37 #7 (1969) (Req:4)
Rear shock absorber springs

99-0122 FROM I-NET 64533645
Bush, bonded
Ref# 18 Fig. 13 Page 37 #7 (1969) (Req:4)
Rear shock absorber

99-0161 SMITHS SSM001/06
Speedometer head MPH
Ref# 1 Fig. 33 Page 73 #7 (1969) (Req:1)
Speedometer

99-0166 SMITHS RSM3003/01
Tachometer
Ref# 30 Fig. 33 Page 73 #7 (1969) (Req:1)
Tachometer T120R-TR6R

99-0220 AMAL 4/048
Screw, twistgrip
Ref# 32 Fig. 28 Page 65 #7 (1969) (Req:2)
Twistgrip T120R

99-0225 AMAL 11/013
Screw
Ref# 18 Fig. 27 Page 63 #7 (1969) (Req:1)
Front brake lever bracket (fore)

99-0226 AMAL 11/014
Screw
Ref# 17 Fig. 27 Page 63 #7 (1969) (Req:1)
Front brake lever bracket (aft)
Ref# 30 Fig. 27 Page 63 #7 (1969) (Req:2)
Clutch lever bracket clamp

99-0228 AMAL 12/556
Lever, choke
Ref# 22 Fig. 27 Page 63 #7 (1969) (Req:1)
Handlebars

99-0230 AMAL 12/595
Clamp, clutch lever bracket
Ref# 29 Fig. 27 Page 63 #7 (1969) (Req:1)
Handlebars

99-0234 AMAL 12/619
Choke control body
Ref# 16 Fig. 27 Page 63 #7 (1969) (Req:1)
Handlebars

99-0238 AMAL 16/008
Spring, friction
Ref# 33 Fig. 28 Page 65 #7 (1969) (Req:1)
Twistgrip T120R

99-0241 AMAL 16/011
Cable stop
Ref# 38 Fig. 28 Page 65 #7 (1969) (Req:2)
Twistgrip T120R

99-0250 AMAL 18/053
Nut, locking ASME 1/4-26TPI Nyloc
Ref# 20 Fig. 27 Page 63 #7 (1969) (Req:1)
Front brake lever fulcrum screw
Ref# 32 Fig. 27 Page 63 #7 (1969) (Req:1)
Clutch lever fulcrum screw

99-0252 AMAL 18/087
Screw, brake lever fulcrum
Ref# 19 Fig. 27 Page 63 #7 (1969) (Req:1)
Front brake
Ref# 31 Fig. 27 Page 63 #7 (1969) (Req:1)
Clutch lever fulcrum screw

99-0261 AMAL 18/754
Lever, clutch Ball end
Ref# 27 Fig. 27 Page 63 #7 (1969) (Req:1)
Handlebars

99-0262 AMAL 18/1754
Lever (ball end), front brake
Ref# 14 Fig. 27 Page 63 #7 (1969) (Req:1)
Handlebars

99-0265 AMAL 18/773
Bracket, clutch lever
Ref# 28 Fig. 27 Page 63 #7 (1969) (Req:1)
Handlebars

99-0266 AMAL 18/776
Lever bracket, front brake
Ref# 15 Fig. 27 Page 63 #7 (1969) (Req:1)
Handlebars

99-0337 AMAL 210/007
Screw, twistgrip friction adjuster
Ref# 34 Fig. 28 Page 65 #7 (1969) (Req:1)
Twistgrip T120R

99-0338 AMAL 210/008
Screw, twistgrip rotor stop
Ref# 35 Fig. 28 Page 65 #7 (1969) (Req:1)
Twistgrip T120R
Orient: Rotor stop screw on top, friction screw on the bottom

99-0339 AMAL 210/009
Nut, twistgrip rotor stop screw
Ref# 36 Fig. 28 Page 65 #7 (1969) (Req:2)
Twistgrip T120R

99-0341 AMAL 244/104
Junction box, choke
Ref# 23 Fig. 28 Page 65 #7 (1969) (Req:1)
Choke cable T120R

99-0345 AMAL 313/008
Twistgrip body, top half
Ref# 29 Fig. 28 Page 65 #7 (1969) (Req:1)
Twistgrip T120R

99-0346 AMAL 313/009
Twistgrip body, bottom half
Ref# 30 Fig. 28 Page 65 #7 (1969) (Req:1)
Twistgrip T120R

99-0347 AMAL 313/013
Twistgrip rotor handle
Ref# 31 Fig. 28 Page 65 #7 (1969) (Req:1)
Twistgrip T120R

99-0351 AMAL 313/13
Twistgrip assembly, complete
Ref# 28 Fig. 28 Page 65 #7 (1969) (Req:1)
Twistgrip T120R

99-0421
Bin M-1 (0/8/0)
Ferrule, cable stop
Ref# 12 Fig. 27#7 (1969) (Req:2)
Throttle

99-0437 AMAL 13/163
Bin M-4 (6/0/0)
Washer, fiber
Ref# 24 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter, banjo bolt T120R
¹ MAP sent wrong part, 376/092 is for monobloc banjo bolt

99-0438 AMAL 376/093
Filter
Ref# 22 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R

99-0441 AMAL 376/100
Bin - (0/3/0)
Jet, main 220
Ref# 12 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R

99-0506 AMAL 622/050
Float chamber
Ref# 20 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R

99-0510 AMAL 622/067
Bin M-3 (4/0/0)
Needle clip
Ref# 15 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R

99-0511 AMAL 622/197
Bin M-2 (1/2/0)
Needle, brass w. Viton tip
Ref# 21 Fig. 31 Page 71 #7 (1969) (Req:2)
Float chamber T120R

99-0512 AMAL 622/069
Bin M-2 (0/3/0)
Float
Ref# 17 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R
¹ British Only sells Stay-Up Floats for $35US each

99-0513 AMAL 622/071
Bin M-2 (0/2/0)
Float spindle
Ref# 18 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R

99-0514 AMAL 622/073
Bin D-8 (5/2/0)
Joint washer
Ref# 19 Fig. 31 Page 71 #7 (1969) (Req:2)
Float bowel (gasket) T120R

99-0515 AMAL 622/076
Screw, air adjustment
Ref# 9 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R
Orient: Out 2 1/4 - 2 1/2 turns. In is richer.
¹ Approx 2 1/2 turns out

99-0516 AMAL 622/077
Screw, throttle valve stop
Ref# 8 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R

99-0517 AMAL 622/078
Bolt, banjo
Ref# 23 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R
Orient: Acute angle > front of bike

99-0520 AMAL 622/082
Bin M-4 (99/0/0)
O-ring Buna-N, size 006 (1/8" X 1/4" X 1/16")
Ref# 10 Fig. 31 Page 71 #7 (1969) (Req:4)
Air adjustment screw T120R

99-0521 622/086
Bin M-2 (1/0/0)
Screw
Ref# 5 Fig. 31 Page 71 #7 (1969) (Req:8)
Carburetter float bowl and cover T120R

99-0527 928/060
Throttle valve #3 cutaway
Ref# 6 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R

99-0528 AMAL 928/062
Bin M-1 (2/2/2)
Air slide, choke
Ref# 26 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R

99-0530 AMAL 928/066
Velocity stack
Ref# 29 Fig. 31 Page 71 #7 (1969)
Carburetter T120R

99-0537 LUCAS 281
Bin A-4 (1/0/0)
Bulb, warning light (281) 2W. BA7S
Ref# 17 Fig. 36 Page 79 #7 (1969) (Req:2)
Headlight shell T120R-TR6R

99-0542
Bin A-4 (2/0/0)
Bulb (380)
Ref# 27 Fig. 36 Page 79 #7 (1969) (Req:1)
Stoplight bulbholder T120R-TR6R
Orient: 6 1/2W. offset pin

99-0545
Bin A-5 (5/1/0)
Bulb, headlight (446) 50/40 W. vert dip, pre-focus (446)
Ref# 7 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell (light unit) T120R-TR6R

99-0548
Bulb, pilot light (989) 6W. MCC (Miniature Center Contact) straight pin
Ref# 9 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell (light unit) T120R-TR6R

99-0552 AMAL 622/101
Bin - (3/0/0)
O-ring Thin: Viton/Dash#28/Nom.CS 1/16"/ID 1-3/8"
Ref# 3 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter flange T120R
¹ #7 Error. Use thick o'ring 70-9711 instead

99-0555 AMAL 31563
Bin A-2 (1/1/1)
Horn Sw/Dip Sw/Wiring Harness
Ref# 35 Fig. 27 Page 63 #7 (1969) (Req:1)
Handlebars

99-0558 LUCAS 31899
Bin A-3 (1/0/0)
Switch, ignition Type S45
Ref# 30 Fig. 36 Page 79 #7 (1969) (Req:1)
Front forks T120R-TR6R
¹ White to single tab; Brown/White to twin tabs

99-0563 LUCAS 35710
Bin A-3 (0/0/0)
Switch, lighting
Ref# 15 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell T120R-TR6R

99-0568 LUCAS 38189
Bulb holder body, warning light (red)
Ref# 16 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell T120R-TR6R

99-0569 LUCAS 38191
Bulb holder body, warning light (green)
Ref# 18 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell T120R-TR6R

99-0588
Bin B-2 (0/0/1)
Condenser Pack 2CP
Ref# 28 Fig. 35 Page 77 #7 (1969) (Req:1)
Condenser pack T120R-TR6C

99-0589 LUCAS 49072
Bin A-1 (0/0/0)
Selenium rectifier, type 2DS 506 Unused lug up, grounding bolt down
Ref# 40 Fig. 35 Page 77 #7 (1969) (Req:1)
Selenium rectifier
¹ Clockwise: White/Green
Brown/White(center),Yellow/Green

99-0590 LUCAS 49345
Bin A-1 (0/1/1)
Zener diode
Ref# 43 Fig. 35 Page 77 #7 (1969) (Req:1)
Zener diode
Torque: 1.5 LBS

99-0597 LUCAS 53973
STOPLIGHT ASSEMBLY, Type L679
Ref# 22 Fig. 36 Page 79 #7 (1969) (Req:1)
Stoplight T120R-TR6R

99-0608 LUCAS 59883
Headlight assembly, Type SS700P
Ref# 1 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell T120R-TR6R

99-0612 LUCAS 70197
Bin P-7 (0/1/1)
Horn, type 6H
Ref# 36 Fig. 35 Page 77 #7 (1969) (Req:1)
Horn

99-0630 AMAL 380459
Rubber backing
Ref# 36 Fig. 27 Page 63 #7 (1969) (Req:1)
Horn and dip switch

99-0683 LUCAS 504665
Bin A-6 (11/0/0)
Fixing wire
Ref# 4 Fig. 36 Page 79 #7 (1969) (Req:6)
Headlight shell T120R-TR6R

99-0686 LUCAS 516798
Headlight unit (reflector/lense)
Ref# 3 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell T120R-TR6R

99-0690 LUCAS 534296
Bin A-6 (0/1/1)
Plate, fixing
Ref# 6 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell and headlight rim T120R-TR6R

99-0692 LUCAS 553248
Bin S1- (2/1/1)
Rim, headlight
Ref# 2 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell T120R-TR6R

99-0695
Bin A-5 (1/1/1)
Bulb holder
Ref# 3 Fig. 33 Page 73 #7 (1969) (Req:2)
Speedo/tachometer
Ref# 10 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell (light unit) T120R-TR6R

99-0701
Contact assembly
Ref# 26 Fig. 36 Page 79 #7 (1969) (Req:1)
Stoplight T120R-TR6R

99-0719
Battery YTX12-BS
Ref# 8 Fig. 24 Page 57 #7 (1969) (Req:1)
Battery
¹ www.batterystuff.com/powersports-batteries/sYTX12-BS.html

99-0725 LUCAS 54033234
Bin A-3 (0/2/1)
Switch, brakelight, type 22B
Ref# 42 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard

99-0737 LUCAS 54170009
Capacitor, ignition
Ref# 1 Fig. 34 Page 75 #7 (1969) (Req:1)
Battery TR6C
¹ Replaces battery

99-0739 LUCAS 54213901
Rotor
Ref# 23 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft, D.S.

99-0757 LUCAS 54415642
Spring set
Ref# 19 Fig. 6 Page 23 #7 (1969) (Req:1)
Auto advance unit
¹ Lucas 54417992 for stronger

99-0767 LUCAS 54420128
Bin - (0/0/1)
Cover, rubber
Ref# 30 Fig. 35 Page 77 #7 (1969) (Req:1)
Condensor

99-0768 LUCAS 54419097
Bin A-9 (0/1/1)
CONTACT BREAKER PLATE ASSEMBLY
Ref# 20 Fig. 6 Page 23 #7 (1969) (Req:1)
Contact breaker

99-0769
Screw, non-centric w pin
Ref# 22 Fig. 6 Page 23 #7 (1969) (Req:2)
Breaker points adjustment

99-0771 LUCAS 54419340
Bin A-8 (0/1/1)
Auto advance unit 12 degree advance for Bonnie
Ref# 18 Fig. 6 Page 23 #7 (1969) (Req:1)
Timing chest

99-0772 LUCAS 54419827
Bin A-9 (4/2/0)
Contact set Gap .014-.016 IN. Check at 1000 MI.
Ref# 21 Fig. 6 Page 23 #7 (1969) (Req:2)
Contact breaker plate
¹ Blk/Yel (Rear) T.S.
Blk/Wht (forward) D.S.

99-0780
Gasket, tail light
Ref# 28 Fig. 36 Page 79 #7 (1969) (Req:1)
Tail light assembly (5451677) T120R-TR6R

99-0783 LUCAS 54574348
Bulb holder, reflector
Ref# 25 Fig. 36 Page 79 #7 (1969) (Req:1)
Tail light T120R-TR6R

99-0803 LUCAS 54945043
Bulb holder, warning light
Ref# 19 Fig. 36 Page 79 #7 (1969) (Req:2)
Headlight shell T120R-TR6R

99-1003
Bulb holder, headlight
Ref# 8 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell (light unit) T120R-TR6R

99-1006 LUCAS 47205
Stator, RM21 (Tool-Wheel puller)
Ref# 18 Fig. 11 Page 33 #7 (1969) (Req:1)
Crankshaft, D.S.

99-1027 LUCAS 33188
Bin P-7 (0/1/1)
Horn relay
Ref# 53 Fig. 35 Page 77 #7 (1969) (Req:1)
Horn relay bracket

99-1030
Reflector, red
Ref# 15 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender

99-1031 AMAL 18/1708/1709
Bin I-6 (0/2/1)
Adjuster and nut
Ref# 21 Fig. 27 Page 63 #7 (1969) (Req:1)
Front brake cable adjuster (handlebars)
Ref# 33 Fig. 27 Page 63 #7 (1969) (Req:1)
Clutch cable adjuster (handlebars)

99-1032 AMAL 928/098
Mixing Chamber top
Ref# 4 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R

99-1033 AMAL 622/131
Spring, throttle valve return
Ref# 7 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R

99-1034 AMAL 622/128
Jet holder
Ref# 11 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R

99-1035 AMAL 622/122
Bin M-3 (2/3/0)
Jet, needle .105(lean).106(medium).107(rich)
Ref# 13 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R
¹ Check with gauges Go-.1058/NoGo-.1062

99-1036 AMAL 622/124
Bin M-3 (0/4/0)
Needle
Ref# 14 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R
Orient: Middle notch
¹ The higher the notch, the richer the mixture.

99-1037 AMAL 928/103
Air valve guide sleeve
Ref# 16 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R

99-1038 AMAL 622/129
Spring, choke
Ref# 27 Fig. 31 Page 71 #7 (1969) (Req:2)
Carburetter T120R

99-1043 LUCAS 47638
Bin B-1 (3/2/0)
Condenser
Ref# 29 Fig. 35 Page 77 #7 (1969) (Req:2)
Condenser

99-1044 LUCAS 36403
Ammeter, type 2AR
Ref# 11 Fig. 36 Page 79 #7 (1969) (Req:1)
Headlight shell T120R-TR6R

99-1045 LUCAS 54955257
Wiring harness
Ref# 21 Fig. 36 Page 79 #7 (1969) (Req:1)
Wiring harness T120R-TR6R

99-1046 LUCAS 54577109
Bin S-1 (0/0/1)
Lense
Ref# 23 Fig. 36 Page 79 #7 (1969) (Req:1)
Tail light T120R-TR6R

99-1047 FROM I-NET 64544234
Spring, H.D. chrome 145 lbs.
Ref# 20 Fig. 13 Page 37 #7 (1969) (Req:2)
Shock absorber

99-1048 FROM I-NET 64543708
Spring, chrome 100 lbs.
Ref# 20 Fig. 13 Page 37 #7 (1969) (Req:2)
Shock absorber

99-1153 AMAL 622/151
Bin M-4 (4/0/0)
Washer, fiber
Ref# 27 Fig. 7 Page 29 1971 PARTS (Req:2)
Carburetter drain plug

DS47 / DS47
Nut ASME 7/16-26TPI Thin (Tool-7/16BS)
Ref# 3 Fig. 14 Page 39 #7 (1969) (Req:4)
Engine mounting studs
¹ Studs, Ref.1, Ref.4

DS73 / DS73
Nipple
Ref# 4 Fig. 28 Page 65 #7 (1969) (Req:1)
Clutch cable

EOF