Nuts,<br><font size=-1>by Part Number</font>

Nuts,
by Part Number
9 May 2023

PO172A
Nut, plain ASME 3/8-26TPI (Tool-3/8BS 5/16W)
Ref# 28 Fig. 14 Page 39 #7 (1969) (Req:3)
Brake pedal
¹ '65-'69 PO172; '70 99-0047; Best# PO172A.

S1-51
Bin E-7 (2/0/0)
Nut (crankcase junction studs) CEI/BSC/Cycle 5/16-26TPI
Ref# 36 Fig. 2 Page 15 #7 (1969) (Req:8)
Crankcase

S1-52
Bin - (2/0/0)
Nut ASME 3/8-26TPI Thin (Tool-3/8BS 5/16W)
Ref# 26 Fig. 14 Page 39 #7 (1969) (Req:4)
Torque stay, head bolts 21/38 (bolts 2,3,4,5)
Ref# 34 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear brake cam lever
Torque: 20 LBS

14-
14-0301
Bin E-1 (2/2/1)
Nut, plain UNF (SAE) 1/4-28TPI (Tool-11mm)
Ref# 15 Fig. 9 Page 29 #7 (1969) (Req:4)
Gearchange guideplate
Ref# 7 Fig. 15 Page 41 #7 (1969) (Req:4)
Exhaust crossover pipe clip
Ref# 25 Fig. 35 Page 77 #7 (1969) (Req:6)
Ignition coil bracket to frame T120R-TR6C
Ref# 56 Fig. 35 Page 77 #7 (1969) (Req:6)
Horn relay bracket

14-0302
Bin E-1 (6/2/0)
Nut, plain UNF (SAE) 5/16-24TPI (Tool-1/2)
Ref# 31 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover, bottom stud
Ref# 34 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard, stepped bolt 37/32
Ref# 12 Fig. 14 Page 39 #7 (1969) (Req:4)
Engine mount plates
Orient: Nuts out
¹ To 14-0220 bolts (Fig.14 Ref.8), D.S. Fore Top & Middle
Ref# 31 Fig. 14 Page 39 #7 (1969) (Req:2)
Torque stays
Ref# 21 Fig. 15 Page 41 #7 (1969) (Req:4)
Muffler hanger (to frame)
¹ Hanger-to-frame w washer Ref.22, and bolt Ref.20
Ref# 25 Fig. 15 Page 41 #7 (1969) (Req:2)
Muffler hanger
¹ Hanger-to-muffler-bracket w washer Ref.24 and bolt Ref.23
Ref# 27 Fig. 19 Page 49 #7 (1969) (Req:2)
Front brake cam spindle
Torque: 20 LBS
Ref# 28 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, rear frame clip
Ref# 19 Fig. 29 Page 67 #7 (1969) (Req:2)
Passenger footrest hanger

14-0303
Bin E-1 (9/1/1)
Nut, plain UNF (SAE) 3/8-24TPI (Tool-9/16)
Ref# 21 Fig. 2 Page 15 #7 (1969) (Req:2)
Crankcase junction stud TS (Ref.19)
Ref# 18 Fig. 12 Page 35 #7 (1969) (Req:2)
Main/rear frame (top)
Ref# 25 Fig. 13 Page 37 #7 (1969) (Req:4)
Rear shock absorber mount, top/bottom
Orient: Nuts out or it scrapes brake drum cover
Ref# 22 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine mount plate, bottom bolts both sides

14-0304
Bin E-1 (2/0/0)
Nut, plain UNF (SAE) 7/16-20TPI (Tool-7/16BS 3/8W)
Ref# 21 Fig. 12 Page 35 #7 (1969) (Req:2)
Main/rear frame, bottom front, bolt 35/19
Ref# 14 Fig. 13 Page 37 #7 (1969) (Req:2)
Torque stay, front (swingarm) and rear (brake plate)

14-0305
Nut, plain UNF (SAE) 1/2-20TPI (Tool-19mm(3/4") Socket)
Ref# 18 Fig. 14 Page 39 #7 (1969) (Req:2)
Driver footrests (both)

14-0401
Nut, locking UNF (SAE) 1/4-28TPI thin locking
Ref# 35 Fig. 14 Page 39 #7 (1969) (Req:1)
Brake pedal stop
Ref# 31 Fig. 19 Page 49 #7 (1969) (Req:1)
Front brake, threaded fork end

14-0402
Bin E-2 (1/3/1)
Nut, locking UNF (SAE) 5/16-24TPI thin locking
Ref# 24 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, center and front stays to bracket (R#5)
Orient: Nuts face out

14-0403
Bin E-2 (2/0/0)
Nut, locking UNF (SAE) 3/8-24TPI thin locking (Tool-9/16)
Ref# 18 Fig. 10 Page 31 #7 (1969) (Req:1)
Clutch adjuster pin
Ref# 27 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine mount plates, bolts 39/23, top/rear, both sides
Orient: Head in, nut out

14-0404
Bin P-2 (2/0/0)
Nut, locking UNF (SAE) 7/16-20TPI thin locking (Tool-11/16")
Ref# 9 Fig. 12 Page 35 #7 (1969) (Req:2)
Center stand '69/'70 650
¹ Goes with '69-'70 center stands (83-1267)

14-0701
Nut, locking UNF (SAE) 1/4-28TPI thin Philidas
Ref# 25 Fig. 23 Page 55 #7 (1969) (Req:2)
Battery holder straps, front/rear

14-0702
Bin E-3 (3/2/2)
Nut, locking UNF (SAE) 5/16-24TPI thin Philidas (Tool-13mm deep socket)
Ref# 23 Fig. 11 Page 33 #7 (1969) (Req:3)
Stator studs
Torque: 20 LBS
Ref# 31 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard, front mount
Ref# 29 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, bottom stay

14-0703
Bin E-3 (2/0/0)
Nut, locking UNF (SAE) 3/8-24TPI thin Philidas
Ref# 13 Fig. 12 Page 35 #7 (1969) (Req:1)
Side stand bolt F7021
Orient: Nut faces out

14-1201
Bin E-4 (11/0/0)
Nut, locking UNF (SAE) 1/4-28TPI Cleveloc (Tool-9/16)
Ref# 22 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, center stay to fender
Ref# 22 Fig. 26 Page 61 #7 (1969) (Req:2)
Front fender, front stay to fender
Ref# 22 Fig. 26 Page 61 #7 (1969) (Req:1)
Front fender, rear stay to fender
Ref# 22 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, liscense plate bracket
Ref# 22 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, bridge
Ref# 22 Fig. 26 Page 61 #7 (1969) (Req:2)
Rear fender, lifting handle
Ref# 22 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender, frame bracket, top

14-1301
Bin M-5 (2/1/0)
Nut, locking UNF (SAE) 1/4-28TPI thin Cleveloc
Ref# 52 Fig. 2 Page 15 #7 (1969) (Req:1)
Protection blade
Ref# 33 Fig. 31 Page 71 #7 (1969) (Req:4)
Carburetter adaptor 21/12, 21/13 (mount stud) T120R
¹ RPC #7 incorrectly lists part number S1932 (21-1932)

14-1302
Bin E-5 (4/1/1)
Nut, locking UNF (SAE) 5/16-24TPI thin Cleveloc
Ref# 36 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust crossover pipe
Ref# 25 Fig. 22 Page 53 #7 (1969) (Req:2)
Gas tank, front tank mount

14-1303
Nut, locking UNF (SAE) 3/8-24TPI thin Cleveloc (Tool-9/16)
Ref# 6 Fig. 17 Page 45 #7 (1969) (Req:2)
Stanchion tube pinch bolt 45/4
Torque: 25 LBS

14-1902
Nut, locking UNF (SAE) 5/16-24TPI thin Aerotite (Tool-1/2)
Ref# 43 Fig. 20 Page 51 #7 (1969) (Req:2)
Rear wheel chain adjuster

14-1903
Bin I-1 (2/2/0)
Nut, locking UNF (SAE) 3/8-24TPI thin Aerotite (Tool-9/16)
Ref# 20 Fig. 18 Page 47 #7 (1969) (Req:2)
Handlebar mount T120R-TR6R
¹ Dummy notes line one

21-
21-0544 / S544
Bin K-8 (1/0/0)
Nut, domed UNF (SAE) 5/16-24TPI (Tool-1/2")
Ref# 46 Fig. 9 Page 29 #7 (1969) (Req:1)
Gearbox outer cover, upper stud
Ref# 36 Fig. 11 Page 33 #7 (1969) (Req:2)
Primary chaincase cover (stator studs)
Torque: 10 LBS

21-0545 / S545
Nut UNC (SAE) 9/16-12TPI (Tool-15/16)
Ref# 10 Fig. 13 Page 37 #7 (1969) (Req:1)
Swinging fork, bolt 37/8
Torque: 45 LBS

21-0586 / S586
Bin L-5 (1/1/0)
Nut, locking UNF (SAE) 9/16-18TPI -Locktite 243 (blue) (Tool-Lock-plate & 7/8")
Ref# 1 Fig. 10 Page 31 #7 (1969) (Req:1)
Clutch securing nut
Torque: 50 LBS
¹ Renew after removing

21-0594 / S594
Bin K-3 (1/2/0)
Nut UNF (SAE) 9/16-18TPI Thin (Tool-15/16")
Ref# 26 Fig. 8 Page 27 #7 (1969) (Req:1)
Kickstarter ratchet
Torque: 45 LBS
¹ Blue Loctite

21-0672 / S672
Nut UNF (SAE) 5/16-24TPI
Ref# 6 Fig. 28 Page 65 #7 (1969) (Req:1)
Clutch cable

21-0685 / S685
Bin I-2 (1/0/0)
Nut, seated UNF (SAE) 3/8-24TPI
Ref# 16 Fig. 17 Page 45 #7 (1969) (Req:1)
Upper yoke pinch bolt
Torque: 15 LBS

21-0692 / S692
Bin 0-2 (0/8/8)
Nut UNF (SAE) 3/8-24TPI 12 points
Ref# 3 Fig. 5 Page 21 #7 (1969) (Req:8)
Cylinder block base
Torque: 35 LBS

21-1906 / S1906
Bin - (2/0/0)
Nut, conical UNF (SAE) 1/4-28TPI
Ref# 12 Fig. 3 Page 17 #7 (1969) (Req:2)
Oil pump
Torque: 5 LBS

21-1908 / S1908
Bin H-5 (3/0/0)
Nut, plain UNF (SAE) 5/16-24TPI tall 7/16AF (Tool-1/2)
Ref# 31 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust pipe to muffler clamp, bolt 41/29

21-1932 / S1932
Nut, locking
Ref# 16 Fig. 5 Page 21 #7 (1969) (Req:2)
Carburetter adaptor/Cylinder head
¹ E4608(BSC 20) in #7:up to'68. Use 21-1932(UNF 16tpi) 1969-on

21-2016 / S549
Bin S-M (0/4/0)
Nut, locking UNF (SAE) 5/16-24TPI
Ref# 11 Fig. 1 Page 13 #7 (1969) (Req:4)
Con rod
Torque: 28 LBS

30-
30-276-037-11
Bin B-9 (4/0/0)
Nut
Ref# 7 Fig. 33 Page 73 #7 (1969) (Req:4)
Speedo/tach mount

37-
37-1691 / W1691
Nut, locking ASME 5/16-26TPI
Ref# 13 Fig. 20 Page 51 #7 (1969) (Req:8)
Brakedrum to hub

37-2058 / W2058
Nut 3/4"
Ref# 33 Fig. 19 Page 49 #7 (1969) (Req:1)
Front brake anchor plate

37-3425 / W3425
Nut UNF (SAE) Thickness: 3/4"(.470")(15/32"); Flats: 1.306" (1-5/16")
Ref# 46 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel spindle, D.S. (inside)
¹ Inside nut, D.S.

37-3426 / W3426
Nut UNF (SAE) Thickness: 3/4"(.322"); Flats: 1.317"(<1-5/16")
Ref# 24 Fig. 20 Page 51 #7 (1969) (Req:1)
Rear wheel spindle, T.S. (inside)
¹ Inside nut, T.S.

54130041
Nut
Ref# 31 Fig. 36 Page 79 #7 (1969) (Req:1)
Ignition switch T120R-TR6R

57-
57-0440 / T440
Bin K9-S3 (2/4/0)
Nut CEI/BSC/Cycle 1 1/4" (Tool-Z63)
Ref# 14 Fig. 8 Page 27 #7 (1969) (Req:1)
Mainshaft, gearbox sprocket
Torque: 50 LBS
¹ Blue Loctite. Remove w. air wrench.

57-2526 / T2526
Nut ASME 1/4-26TPI
Ref# 21 Fig. 10 Page 31 #7 (1969) (Req:3)
Clutch pressure plate spring adjustment

70-
70-0470 / E0470
Bin O-5 (0/4/0)
Nut CEI/BSC/Cycle 5/16-26TPI .038 Pitch (Tool-3/16W or adj tool)
Ref# 48 Fig. 5 Page 21 #7 (1969) (Req:4)
Valve adjuster lock
¹ Adj at 3Kmi (ha-ha)
1/4 turn=.01"
Ex.004" In.002"

70-1310 / E1310
Bin N-2 (1/0/0)
Nut CEI/BSC/Cycle 5/16-26TPI Thin Wall (Tool-1/4 BS)
Ref# 15 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil pipes and junction block

70-1435 / E1435
Bin O-6 (2/2/2)
Nut, domed ASME 3/8-26TPI (Tool-3/8BS 5/16W)
Ref# 34 Fig. 23 Page 55 #7 (1969) (Req:2)
Rocker oil feed pipe
Torque: 22 LBS
¹ Changed to 24TPI (UNF) in 1973; beware of mismatches

70-1463 / E1463
Bin N-2 (0/0/0)
Nut (inlet camshaft pinion) LEFT-HAND (Tool-1")
Ref# 33 Fig. 1 Page 13 #7 (1969) (Req:1)
Camshaft, inlet

70-3977 / E3977
Nut, shouldered ASME 7/16-26TPI - Locktite 243 (blue)
Ref# 25 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft, D.S.
Torque: 30 LBS
¹ Lock clutch basket, not brake for accurate torque reading

70-4563 / E4563
Bin N-5 (0/1/0)
Nut (exhaust camshaft pinion) LEFT-HAND (Tool-5/8W, 11/16BSF)
Ref# 34 Fig. 1 Page 13 #7 (1969) (Req:1)
Camshaft, exhaust

70-4565 / E4565
Bin N-5 (0/0/0)
Nut (crankshaft pinion) 3/4-20TPI (Tool-5/8W, 11/16BS)
Ref# 28 Fig. 1 Page 13 #7 (1969) (Req:1)
Crankshaft, T.S.
Torque: 30/80LBS
¹ Late '71 models w UN crankshaft threads use nut 71-2877

70-6596 / E6596
Nut, domed (release valve cap) (Tool-15/16)
Ref# 16 Fig. 3 Page 17 #7 (1969) (Req:1)
Oil release valve, crankcase T.S.

70-7471 / E7471
Nut, locking ASME 1/4-26TPI Nyloc (Tool-7/16")
Ref# 14 Fig. 15 Page 41 #7 (1969) (Req:2)
Exhaust pipe bracket/exhaust pipe

70-8992 / E8992
Bin L-7 (0/2/1)
Nut, sleeve UNC (SAE) 1/2-13TPI
Ref# 19 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chaincase

70-9703 / E9703
Nut, sleeve (Tool-D496)
Ref# 14 Fig. 11 Page 33 #7 (1969) (Req:1)
Primary chain tensioner

71-
71-3799 / F3799 LUCAS 166043
Nut
Ref# 6 Fig. 35 Page 77 #7 (1969) (Req:4)
Ignition coil

82-
82-0879 / F879
Bin E-6 (3/0/0)
Nut CEI/BSC/Cycle 1/4-26TPI (Tool-1/4BS 3/16W open)
Ref# 34 Fig. 5 Page 21 #7 (1969) (Req:6)
Rocker box mount stud
Torque: 5 LBS
Ref# 36 Fig. 13 Page 37 #7 (1969) (Req:1)
Chainguard, C-clamp
Ref# 30 Fig. 23 Page 55 #7 (1969) (Req:2)
Oil tank mount, upper
Ref# 39 Fig. 26 Page 61 #7 (1969) (Req:1)
Rear fender, stud 61/38 stoplight adaptor (to fender)

82-1747 / F1747
Nut, plain UNF (SAE) 3/4"; .436" (7/16") thick; 1.099" (<1-7/64") across flats
Ref# 44 Fig. 20 Page 51 #7 (1969) (Req:2)
Rear wheel spindle, T.S./D.S. (outside)
Torque: 90 LBS
¹ Outside nuts on T.S./D.S.

82-2725 / F2725
Bin P-1 (1/3/0)
Nut, locking BSPP
Ref# 9 Fig. 12 Page 43 #4 (Req:2)
Center stand '64-'68 650
¹ Goes with '65-'68 center stands (82-5932)

82-3182 / F3182
Nut, union (Tool-3/8BS 5/16W)
Ref# 9 Fig. 23 Page 55 #7 (1969) (Req:1)
Oil tank pipe, filter

82-3799 / F3799
Bin B-4 (3/4/0)
Nut
Ref# 37 Fig. 26 Page 61 #7 (1969) (Req:1)
Stoplight
Ref# 35 Fig. 35 Page 77 #7 (1969) (Req:2)
Condenser bracket
Ref# 38 Fig. 35 Page 77 #7 (1969) (Req:3)
Horn mount

82-4717 / F4717
Bin A-3 (1/0/0)
Nut, locking BA 2BA
Ref# 44 Fig. 13 Page 37 #7 (1969) (Req:3)
Brakelight switch
¹ #7 says Qty.5 (p.37) Only find 3
Ref# 44 Fig. 13 Page 37 #7 (1969) (Req:1)
Brakelight switch lever

82-5338 / F5338
Nut ASME 1/4-26TPI
Ref# 41 Fig. 35 Page 77 #7 (1969) (Req:1)
Selenium rectifier mount

82-7387 / F7387
Bin I-9 (2/0/0)
Nut, sleeve UNF (SAE) 1/4-28TPI
Ref# 41 Fig. 13 Page 37 #7 (1969) (Req:1)
Brake operating rod adjustment

82-7389 / F7389
Nut (Tool-3/4)
Ref# 41 Fig. 14 Page 39 #7 (1969) (Req:2)
Engine mount plates, stud 39/21
Torque: 100 LBS

82-8034 / F8034
Bin E-6 (4/0/0)
Nut, sleeve UNF (SAE) 1/4-28TPI (Tool-9/16")
Ref# 40 Fig. 23 Page 55 #7 (1969) (Req:1)
Battery holder strap, front (common connection)

83-
83-0006 / F10006
Bin M-6 (1/0/0)
Nut UNC (SAE) 1/2 x 13TPI (Tool-7/16BS 3/8W)
Ref# 18 Fig. 22 Page 53 #7 (1969) (Req:2)
Gas tank, gas tap

83-0222 / F10222
Bin P-4 (1/0/0)
Nut, panel
Ref# 4 Fig. 25 Page 59 #7 (1969) (Req:1)
Side panel

97-
97-0919 / H919
Nut BA 4BA
Ref# 12 Fig. 22 Page 53 #7 (1969) (Req:1)
Gas tank, center styling strip

97-2091 / H2091
Nut, bearing
Ref# 32 Fig. 17 Page 45 #7 (1969) (Req:2)
Bottom of stanchion tube

97-2108 / H2108
Bin I-2 (1/1/1)
Nut, sleeve (fork stem)
Ref# 12 Fig. 18 Page 47 #7 (1969) (Req:1)
Front forks TR6C
¹ Replaces 97-2263 for damper

97-2245 / H2245
Nut 1 1/2" across flats
Ref# 33 Fig. 17 Page 45 #7 (1969) (Req:2)
Stanchion tube cap
Torque: 80 LBS

97-2263 / H2263
Bin I-2 (0/1/1)
Nut, sleeve (fork stem)
Ref# 7 Fig. 17 Page 45 #7 (1969) (Req:1)
Front forks

97-408 / H408
Nut, sleeve
Ref# 12 Fig. 18 Page 47 #7 (1969) (Req:1)
Steering damper

99-
99-0250 AMAL 18/053
Nut, locking ASME 1/4-26TPI Nyloc
Ref# 20 Fig. 27 Page 63 #7 (1969) (Req:1)
Front brake lever fulcrum screw
Ref# 32 Fig. 27 Page 63 #7 (1969) (Req:1)
Clutch lever fulcrum screw

99-0339 AMAL 210/009
Nut, twistgrip rotor stop screw
Ref# 36 Fig. 28 Page 65 #7 (1969) (Req:2)
Twistgrip T120R

DS47 / DS47
Nut ASME 7/16-26TPI Thin (Tool-7/16BS)
Ref# 3 Fig. 14 Page 39 #7 (1969) (Req:4)
Engine mounting studs
¹ Studs, Ref.1, Ref.4

EOF